Uniden DXAI 5188-2 Series manual Liquid Damage, Case Action

Page 62

Liquid Damage

Moisture and liquid can damage your cordless phone. In case of accidental submersion, please read the following steps.

Case	Action
If the handset or base is exposed to	Wipe off the liquid, and use as normal.
moisture or liquid, but liquid only
affects the exterior plastic housing.

If moisture or liquid has entered the	Handset:
plastic-housing (i.e. liquid can be	1. Remove the battery cover and leave it off for ventilation.
heard in the phone or liquid has	2. Remove the battery pack by disconnecting.
entered the handset battery	3. Leave the battery cover off and the battery pack disconnected for at least 3 days.
compartment or vent openings on the	4. Once the handset is completely dry, reconnect the battery pack and the battery cover.
base).	5. Recharge the handset’s battery pack for 20 hours before using again.

Base:

1.Disconnect the AC adapter from the main base unit, cutting off electrical power.

2.Disconnect the telephone cord from the main base unit.

3.Let dry for at least 3 days.

IMPORTANT: You must unplug the telephone line while recharging the battery pack to avoid charge interruption.

CAUTION:

DO NOT use a microwave oven to speed up the drying process. This will cause permanent damage to the handset, base and the microwave oven.

After following these steps, if your cordless telephone does not work, please send to: Uniden America Corporation

Parts and Service Division

4700 Amon Carter Blvd. Ft. Worth, TX76155

1-800-554-3988. Monday through Friday 8 a.m. to 5 p.m. CST

[ 62 ] A D D I T I O N A L I N F O R M AT I O N

www.uniden.com

Image 62

Contents Page Page Contents Welcome Features Controls and Functions HandsetsMain Base Unit Extra Charging Cradle for Second HandsetDo the following steps Installing the PhoneChoose the best location Install the rechargeable battery packs into both handsets Low battery alert Cleaning the battery charging contactsConnect the main base unit and charging cradle For assistance Modular Mounting the Main Base Unit on a Wall Standard wall plate mountingDirect wall mounting Register Handsets to the Main Base Before Using To transfer a call When to Re-register HandsetsCall Transfer Feature To receive a transfer call from the second handsetEntering your Area Code Setting Menu Display OptionsSetting AutoTalk and Cidcw Choosing the dialing mode Setting the language Making and Receiving Calls Earpiece volume Adjusting the Handset Ringer and Earpiece VolumeHandset ringer tone and volume Temporarily Mute RingerTone Dialing Switch Over Traveling Out-of-RangeFind Handsets Using Call WaitingSelecting a Different Channel Press memory or select/channel Storing Phone Numbers and Names in Speed Dial MemoryVol Press memory or select/channel. Store Number is displayed Steps for Entering Names and Special Characters If you make a mistake while entering a nameMemory dialing from Standby Mode Making Calls from Speed Dial MemorySpeed dialing from Talk Mode Chain DialingEditing a Stored Name and/or Phone Number Press memory or select/channel againPress end to return to standby mode Erasing a Stored Name and Phone Number Press select/channel or delete/transferMaking Calls with the RocketDial RocketDialStoring and Editing the RocketDial Press select/channelDeleting the RocketDial When the Telephone Rings Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID Message List Press call id/menuDeleting all Caller ID names/numbers Deleting Information from the Caller ID ListDeleting a Caller ID message Press delete/transferDisplay returns to the summary screen Making a Call from the Caller ID List Storing Caller ID Messages in Memory Dialing Press call id/menu, then press vol/ / or vol/ / toIntegrated Answering Device Turning the Answering System On/Off Presstalk/flash Setting Up Your Answering SystemAnswering System Setting Setting the Time Setting a Personal Security Code PIN Setting the Ring Time Announce only feature Selecting the Message Record TimeSetting the Message Alert tone Selecting the Language Setting Your Outgoing Message GreetingPreset message Recording a personal outgoing message GreetingSetting the Base Ringer Volume Choosing between the two outgoing messagesTemporarily Mute the Base Ringer Using Your Answering SystemAdjusting the Speaker Volume Level Playing your messages Repeating a messageSkipping a message Deleting a Message Voice memo Recording a conversationRemote access Turn on the answering system remotely To attach the beltclip Installing the BeltclipChanging the Digital Security Code To remove the beltclipPower Failure Headset InstallationBattery replacement and handling Troubleshooting Symptom Suggestion Charge/in use orSymptom Suggestion Memory may be full. Delete some or all of the saved messages Symptom Suggestion Liquid Damage Case ActionAC Adapter Information Battery InformationGeneral Information FrequencyPrecautions Installation Considerations Terminal Equipment Radio Equipment Index K, LPage Remote Operation Card Task Key At Uniden, we´ll take care of you