JVC hr-dvs3u manual 36 EN, Select the DV deck, Press DV

Page 36

36 EN

PLAYBACK/RECORDING ON DV DECK

Basic Playback

(DV deck)

Turn on the TV and select the AV mode.

1

3

2

T

W

1 2 3

2

4 5 6

7 8 9

04

 

1

 

 

 

 

 

 

DV

 

 

 

S-VHS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A Load a cassette.

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointed toward the VCR.

Do not apply too much pressure when inserting.

The VCR’s power comes on automatically.

If the erase protection switch is set to “SAVE”, playback begins automatically. It takes about 15 seconds until the playback picture appears.

B Select the DV deck.

Press DV.

The DV button lights on the VCR.

C Find the program start point.

If the tape is advanced past the start point, press

REW (3) or turn the ADVANCED JOG dial to the left. To go forward, press FF (5) or turn the ADVANCED JOG dial to the right.

D Start playback.

Press PLAY (4).

The DV playback indicator lights on the VCR.

E Stop playback.

Press STOP (8). Then press EJECT () to remove the cassette.

The DV playback indicator turns off.

Usable cassettes

Only cassettes marked

can be used with the DV

deck.

 

NOTE:

When you record a tape on the DV deck with the recording speed set to “LP”, it is recommended to play back the tape on this DV deck. Digital video recorder from other manufacturers may not be able to play back the tape properly.

Image 36
Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationImportant Product Safety Instructions Accessories CleaningDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel How To Use Remote10 EN ON-SCREEN Display for VHS deckTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Check the contents Connect the VCR to power source12 EN Situate the VCR8To connect to a TV with S-VIDEO/AUDIO input connectors Video ConnectionPerform Plug & Play setup What to do if Plug & Play setting failedPlug & Play Set 14 ENLanguage Access the Clock Set screen Clock Set16 EN PreparationsSemiauto Clock Set Manual Clock SetAccess the Tuner Set screen Tuner Set18 EN Auto Channel SetManual Channel Set Add or skip the desired channelsTo add channels To skip channelsInstalling Controller 20 ENAccess the Cable Box Set screen Turn on the cable boxSelect the cable box’s channel If you do not use a cable box, press rt until OFF22 EN Enter the cable box’s brandPress OK or e If the cable box’s channel does not change toIf your DBS receiver has audio/video output connectors How to control the DBS receiverDBS receiver Setting DBS receivers brand and channel Turn on the DBS receiverSelect the DBS receiver’s channel If you do not use a DBS receiver, press rt until OFFEnter the DBS receiver’s brand If the DBS receiver’s channel does not change as shown aboveBasic Playback 26 ENVHS deck Choose a program Set the tape speedStart recording Pause/Resume recording28 EN Slow Motion On the VCRPause during playback Activate frame-by-frame playbackSlow Motion On the Remote Variable Speed Search On the Remote30 EN Index SearchRepeat Playback Next Function MemoryAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingInstant Timer Recording ITR 32 ENRecord One Program While Watching Another Reset the counter Press C.RESET before starting recording or playbackTape Remaining Time Set the counter display34 EN RetakeSecond Audio Recording Active Video Calibration PlaybackRecording 36 EN DV deckSelect the DV deck Press DVDV recording indicator lights on the VCR 38 EN Slow Motion On the Remote 40 EN Time Code Access the PlusCode No. screen Access the VCR Plus+ Program screen42 EN Select the deckEngage the VCR’s timer mode For the VHS deckFor the DV deck Cable Box or DBS Receiver UsersAccess the Guide Channel Set screen 44 ENGuide Channel Number Set Enter the Guide Channel numberGuide Channel Number Enter the receiving channel position numberExpress Timer Programing 46 ENEnter the program date Enter the channel positionPress DATE+ Press CH+Enter the program mode 24HR Quick Programing48 EN Set the program start/stop time and channelPage Disengage the timer mode Access the Program Check screenCancel or change a program Return to the timer modeCancel or change program setting Confirm the overlapping programsSelect the program to modify Overlapping programs blink on the TV screenTape Dubbing 52 ENFrom DV to VHS Dubbing An Entire CassetteFrom VHS to DV Press DV, then press SP/LP p54 EN Locate the start point on the DV deckPrepare the VHS deck for dubbing Pause dubbingLocate the start point on the VHS deck Prepare the DV deck for dubbing56 EN Recorder PlayerSet the input mode of recording deck 58 ENStart the source player Start the recording deckConnection to a PC with DV connector Example When using this VCR as the source playerPC with DV connector Connection to another VCRAudio Dubbing 60 ENVHS Audio Dubbing DV Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB Insert Editing 62 ENVHS Insert Editing Source tapeEngage the Insert Editing mode AV Insert Editing VHS deck onlyPrepare the recording cassette Start EditingAccess the R.A.Edit screen 64 ENSelect the program Press R.A.EDIT. The R.A.Edit screen appearsLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingRemote A/B Code Switching 66 ENChange the code for VCR To control two VCRs with the same RemoteTV Multi-Brand Remote Control Set the TV brand codeOperate the TV Before performing the following stepsPress the corresponding button Power 68 ENSet the Cable Box brand code Operate the Cable BoxDBS Receiver Multi-Brand Remote Control Set the DBS receiver brand codeOperate the DBS receiver Mode Set Access the Mode Set screenSelect the mode Select the mode settingMode SET When this function is set to onVHS Mode SET 72 ENVHS Mode SET 74 EN For ExampleCorrection to the luminance signal to enhance details Selecting either HI-FI L or HI-FI RNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played backDV Mode SET 76 ENPower 78 EN RecordingVHS deck DV deckTimer Recording 80 ENTimer Recording PlaybackRecording 82 EN Cable box Cable Box Control Setting Changing VCR Plus+ SettingExpress Timer Programming VCR Plus+ Timer ProgramingHOW to Locate Your JVC Service Center 84 ENWarranty Only in U.S.A 86 EN
Related manuals
Manual 88 pages 19.11 Kb