JVC hr-dvs3u manual Engage the Audio Dubbing mode, End Audio Dubbing, Press A.DUB

Page 61

EN 61

A Make connections.

Connect an audio component to the AUDIO L + R input connectors on the VCR’s front panel.

●When connecting a monaural audio component, use only the VCR’s AUDIO L input connector.

B Load a cassette.

For the VHS deck

Insert a VHS (or S-VHS) cassette with the record safety tab intact, or cover the hole using adhesive tape.

For the DV deck

Insert a Mini DV cassette with the erase protection switch set to “REC”.

C Set the VCR’s input mode.

Press AUX (number key “0”) and/or CH +/– to select “F-1”.

D Select the recording deck.

Press S-VHSor DV.

●When using the DV deck as the recording deck, press so that the audio signals from the AUDIO L + R input connectors can be recorded. The dubbing direction indicator ( S-VHS) lights.

E Locate the start point.

Press PLAY (4) to start playback of the tape in your VCR, and press PAUSE (9) when you reach the point where you want to start dubbing.

F Engage the Audio Dubbing mode.

Press A.DUB.

●Your VCR enters the Audio Dubbing Pause mode. (“o” blinks, “u” and “i” light up on the front display panel.)

G Start dubbing.

Engage the audio component’s Play mode, then press PLAY (4) to start the tape in your VCR; Audio Dubbing begins at this point.

●“o” blinks and “u” is displayed on the front display panel.

●To stop dubbing temporarily, press PAUSE (9). Press PLAY (4) to resume dubbing.

H End Audio Dubbing.

Press STOP (8) to stop the tape in your VCR, and engage the audio component’s Stop mode.

NOTES:

●Once the Audio Dubbing starts, you can not use the other deck.

●When monitoring the audio-dubbed sound on the DV deck, set “12BIT MODE” to “SOUND2” ( pg. 76).

●When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to

hear the mixed sound (Hi-Fi + Normal soundtracks), press A. MONITOR to select “NORM HI FI” ( pg. 31). (VHS deck only)

●Audio Dubbing stops automatically when the counter reaches “0:00:00”, and the VCR enters the Play mode. Check the counter reading before dubbing. (VHS deck only)

●Audio Dubbing is also possible using the rear panel AUDIO IN connector.

●When playing back an audio-dubbed tape on the VHS deck,

press A. MONITOR on the Remote to select the soundtrack you wish to hear ( pg. 31). When playing back an audio-

dubbed Mini DV tape on the DV deck, set “12BIT MODE” to “SOUND2” ( pg. 76).

●Picture may be distorted during Audio Dubbing Pause.

●It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

●Audio dubbing is not possible using the DV IN/OUT connector.

●Audio dubbing is not possible on a blank portion of the tape.

Page 60 Page 62
Image 61
Page 60 Page 62
Contents For Customer Use Video Cassette RecorderMoisture Condensation Dear CustomerImportant Product Safety Instructions Cleaning AccessoriesDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel Remote How To UseON-SCREEN Display for VHS deck 10 ENTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Connect the VCR to power source Check the contents12 EN Situate the VCRVideo Connection 8To connect to a TV with S-VIDEO/AUDIO input connectorsWhat to do if Plug & Play setting failed Perform Plug & Play setupPlug & Play Set 14 ENLanguage Clock Set Access the Clock Set screen16 EN PreparationsManual Clock Set Semiauto Clock SetTuner Set Access the Tuner Set screen18 EN Auto Channel SetAdd or skip the desired channels Manual Channel SetTo add channels To skip channels20 EN Installing ControllerTurn on the cable box Access the Cable Box Set screenSelect the cable box’s channel If you do not use a cable box, press rt until OFFEnter the cable box’s brand 22 ENPress OK or e If the cable box’s channel does not change toHow to control the DBS receiver If your DBS receiver has audio/video output connectorsDBS receiver Turn on the DBS receiver Setting DBS receivers brand and channelSelect the DBS receiver’s channel If you do not use a DBS receiver, press rt until OFFIf the DBS receiver’s channel does not change as shown above Enter the DBS receiver’s brand26 EN Basic PlaybackVHS deck Set the tape speed Choose a programStart recording Pause/Resume recordingSlow Motion On the VCR 28 ENPause during playback Activate frame-by-frame playbackVariable Speed Search On the Remote Slow Motion On the RemoteIndex Search 30 ENRepeat Playback Next Function MemoryManual Tracking Adjust the tracking manuallySoundtrack Selection Override automatic tracking32 EN Instant Timer Recording ITRRecord One Program While Watching Another Press C.RESET before starting recording or playback Reset the counterTape Remaining Time Set the counter displayRetake 34 ENSecond Audio Recording Playback Active Video CalibrationRecording DV deck 36 ENSelect the DV deck Press DVDV recording indicator lights on the VCR 38 EN Slow Motion On the Remote 40 EN Time Code Access the VCR Plus+ Program screen Access the PlusCode No. screen42 EN Select the deckFor the VHS deck Engage the VCR’s timer modeFor the DV deck Cable Box or DBS Receiver Users44 EN Access the Guide Channel Set screenGuide Channel Number Set Enter the Guide Channel numberEnter the receiving channel position number Guide Channel Number46 EN Express Timer ProgramingEnter the channel position Enter the program datePress DATE+ Press CH+24HR Quick Programing Enter the program mode48 EN Set the program start/stop time and channelPage Access the Program Check screen Disengage the timer modeCancel or change a program Return to the timer modeConfirm the overlapping programs Cancel or change program settingSelect the program to modify Overlapping programs blink on the TV screen52 EN Tape DubbingFrom DV to VHS Dubbing An Entire CassettePress DV, then press SP/LP p From VHS to DVLocate the start point on the DV deck 54 ENPrepare the VHS deck for dubbing Pause dubbingPrepare the DV deck for dubbing Locate the start point on the VHS deck56 EN Player Recorder58 EN Set the input mode of recording deckStart the source player Start the recording deckExample When using this VCR as the source player Connection to a PC with DV connectorPC with DV connector Connection to another VCR60 EN Audio DubbingVHS Audio Dubbing DV Audio DubbingEnd Audio Dubbing Engage the Audio Dubbing modePress A.DUB 62 EN Insert EditingVHS Insert Editing Source tapeAV Insert Editing VHS deck only Engage the Insert Editing modePrepare the recording cassette Start Editing64 EN Access the R.A.Edit screenSelect the program Press R.A.EDIT. The R.A.Edit screen appearsPrepare the source tape Locate the end pointStart Random Assemble Editing End Random Assemble Editing66 EN Remote A/B Code SwitchingChange the code for VCR To control two VCRs with the same RemoteSet the TV brand code TV Multi-Brand Remote ControlOperate the TV Before performing the following steps68 EN Press the corresponding button PowerSet the Cable Box brand code Operate the Cable BoxSet the DBS receiver brand code DBS Receiver Multi-Brand Remote ControlOperate the DBS receiver Access the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to on Mode SET72 EN VHS Mode SETVHS Mode SET For Example 74 ENSelecting either HI-FI L or HI-FI R Correction to the luminance signal to enhance detailsNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played back76 EN DV Mode SETPower Recording 78 ENDV deck VHS deck80 EN Timer RecordingPlayback Timer RecordingRecording 82 EN Changing VCR Plus+ Setting Cable box Cable Box Control SettingExpress Timer Programming VCR Plus+ Timer Programing84 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A 86 EN
Related manuals
Manual 88 pages 19.11 Kb
Top Page Image Contents