JVC hr-dvs3u manual 80 EN, Timer Recording

Page 80

80 EN

 

TROUBLESHOOTING (cont.)

TIMER RECORDING (cont.)

 

 

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

7.

Cable channels are not automatically

● The Controller is not properly

Connect the Controller correctly

 

switched during timer recording.

connected to the VCR.

( pg. 20).

 

 

● The output channel selected in the

After confirming your cable box’s output

 

 

Cable Box Set screen is incorrect.

channel number, re-access the Cable Box

 

 

 

Set screen and select the correct number

 

 

 

( pg. 21).

 

 

● The cable box is turned off.

Make sure the power is on before timer

 

 

 

recording starts.

 

 

 

 

8.

Satellite channels are not

● The Controller is not properly

Connect the Controller correctly

 

automatically switched during timer

connected to the VCR.

( pg. 23).

 

recording.

● The output channel selected in the DBS

After confirming your DBS receiver’s

 

 

 

 

Receiver Set screen is incorrect.

output channel number, re-access the

 

 

 

DBS Receiver Set screen and select the

 

 

 

correct number ( pg. 24).

 

 

● The VCR is not set correctly to control

Set the correct DBS receiver brand code

 

 

the DBS receiver.

( pg. 24).

 

 

● The DBS receiver is turned off.

Make sure the power is on before timer

 

 

 

recording starts.

 

 

 

 

9.

Timer recording begins as scheduled,

● Even though you do not use an external

Set “CABLE BOX SET” to “OFF”

 

but the channel is always incorrect.

cable box or DBS receiver, “CABLE BOX

( pg. 21) or “DBS RECEIVER SET” is set

 

 

SET” is set to “ON” or “DBS RECEIVER

to “OFF” ( pg. 24).

 

 

SET” is set to “ON”.

 

 

 

 

OTHER PROBLEMS

 

 

 

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Whistling or howling is heard from the

● The camcorder’s microphone is too

Position the camcorder so its microphone

 

TV during camcorder recording.

close to the TV.

is away from the TV.

 

 

● The TV’s volume is too high.

Turn the TV’s volume down.

 

 

 

 

2.

When scanning channels, some of

● Those channels have been designated to

If you need the skipped channels, restore

 

them are skipped over.

be skipped.

them ( pg. 19).

 

 

 

 

3.

The channel cannot be changed.

● Recording is in progress.

Press PAUSE (9) to pause the recording,

 

 

 

change channels, then press PLAY (4) to

 

 

 

resume recording.

 

 

 

 

4.

Channel settings that were made

● After the manual settings were made,

Perform manual setting again.

 

manually seem to have changed or

Auto Channel Set was performed.

 

 

disappeared.

 

 

 

 

 

 

5.

The Remote will not operate your TV

● The brand codes are set incorrectly.

Reset the correct brand codes ( pg. 67,

 

or cable box or DBS receiver.

 

68, or 69).

 

 

 

 

6.

Even though Auto or Semiauto Clock

● The clock setting data received from the

Select a different host channel during

 

Set has been performed, the clock is

host channel is incorrect.

“Semiauto Clock Set” ( pg. 17), or

 

incorrect.

 

perform “Manual Clock Set” ( pg. 17).

 

 

 

 

7.

No picture appears when you connect

 

Turn off the VCR or the connected

 

a device to DV IN/OUT connector.

 

appliance once, then turn it on again.

 

 

 

 

ATTENTION

This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the VCR does not operate correctly switch its power off and unplug the AC power cord from the AC supply. Wait for a while and then plug the power cord back in. Eject and check the condition of the cassette. If everything appears normal, you can operate the VCR as usual.

Page 79 Page 81
Image 80
Page 79 Page 81
Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationImportant Product Safety Instructions Accessories CleaningDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel How To Use Remote10 EN ON-SCREEN Display for VHS deckTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Check the contents Connect the VCR to power source12 EN Situate the VCR8To connect to a TV with S-VIDEO/AUDIO input connectors Video ConnectionPerform Plug & Play setup What to do if Plug & Play setting failedPlug & Play Set 14 ENLanguage Access the Clock Set screen Clock Set16 EN PreparationsSemiauto Clock Set Manual Clock SetAccess the Tuner Set screen Tuner Set18 EN Auto Channel SetManual Channel Set Add or skip the desired channelsTo add channels To skip channelsInstalling Controller 20 ENAccess the Cable Box Set screen Turn on the cable boxSelect the cable box’s channel If you do not use a cable box, press rt until OFF22 EN Enter the cable box’s brandPress OK or e If the cable box’s channel does not change toDBS receiver If your DBS receiver has audio/video output connectorsHow to control the DBS receiver Setting DBS receivers brand and channel Turn on the DBS receiverSelect the DBS receiver’s channel If you do not use a DBS receiver, press rt until OFFEnter the DBS receiver’s brand If the DBS receiver’s channel does not change as shown aboveVHS deck Basic Playback26 EN Choose a program Set the tape speedStart recording Pause/Resume recording28 EN Slow Motion On the VCRPause during playback Activate frame-by-frame playbackSlow Motion On the Remote Variable Speed Search On the Remote30 EN Index SearchRepeat Playback Next Function MemoryAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingRecord One Program While Watching Another Instant Timer Recording ITR32 EN Reset the counter Press C.RESET before starting recording or playbackTape Remaining Time Set the counter displaySecond Audio Recording 34 ENRetake Recording Active Video CalibrationPlayback 36 EN DV deckSelect the DV deck Press DVDV recording indicator lights on the VCR 38 EN Slow Motion On the Remote 40 EN Time Code Access the PlusCode No. screen Access the VCR Plus+ Program screen42 EN Select the deckEngage the VCR’s timer mode For the VHS deckFor the DV deck Cable Box or DBS Receiver UsersAccess the Guide Channel Set screen 44 ENGuide Channel Number Set Enter the Guide Channel numberGuide Channel Number Enter the receiving channel position numberExpress Timer Programing 46 ENEnter the program date Enter the channel positionPress DATE+ Press CH+Enter the program mode 24HR Quick Programing48 EN Set the program start/stop time and channelPage Disengage the timer mode Access the Program Check screenCancel or change a program Return to the timer modeCancel or change program setting Confirm the overlapping programsSelect the program to modify Overlapping programs blink on the TV screenTape Dubbing 52 ENFrom DV to VHS Dubbing An Entire CassetteFrom VHS to DV Press DV, then press SP/LP p54 EN Locate the start point on the DV deckPrepare the VHS deck for dubbing Pause dubbingLocate the start point on the VHS deck Prepare the DV deck for dubbing56 EN Recorder PlayerSet the input mode of recording deck 58 ENStart the source player Start the recording deckConnection to a PC with DV connector Example When using this VCR as the source playerPC with DV connector Connection to another VCRAudio Dubbing 60 ENVHS Audio Dubbing DV Audio DubbingPress A.DUB Engage the Audio Dubbing modeEnd Audio Dubbing Insert Editing 62 ENVHS Insert Editing Source tapeEngage the Insert Editing mode AV Insert Editing VHS deck onlyPrepare the recording cassette Start EditingAccess the R.A.Edit screen 64 ENSelect the program Press R.A.EDIT. The R.A.Edit screen appearsLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingRemote A/B Code Switching 66 ENChange the code for VCR To control two VCRs with the same RemoteTV Multi-Brand Remote Control Set the TV brand codeOperate the TV Before performing the following stepsPress the corresponding button Power 68 ENSet the Cable Box brand code Operate the Cable BoxOperate the DBS receiver DBS Receiver Multi-Brand Remote ControlSet the DBS receiver brand code Mode Set Access the Mode Set screenSelect the mode Select the mode settingMode SET When this function is set to onVHS Mode SET 72 ENVHS Mode SET 74 EN For ExampleCorrection to the luminance signal to enhance details Selecting either HI-FI L or HI-FI RNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played backDV Mode SET 76 ENPower 78 EN RecordingVHS deck DV deckTimer Recording 80 ENRecording Timer RecordingPlayback 82 EN Cable box Cable Box Control Setting Changing VCR Plus+ SettingExpress Timer Programming VCR Plus+ Timer ProgramingHOW to Locate Your JVC Service Center 84 ENWarranty Only in U.S.A 86 EN
Related manuals
Manual 88 pages 19.11 Kb
Top Page Image Contents