JVC 0397MKVUNVP, LYT0002-0J9A manual Initializing Jlip, Select Transfer Rate. Normally select

Page 17

INITIALIZATION17

INITIALIZING JLIP

The first time you start the Video Capture software, JLIP initialization is required. This sets which of the computer’s COM ports (connector into which the RS-232C cable is plugged) is connected to the GV-DS1 JLIP Video Capture Docking Station. The initialization window automatically appears the first time you start the software after installation. Do not forget to carry out this JLIP initialization procedure. The JLIP must be initialized again whenever you connect a new image source or other unit to the JLIP Video Capture Docking Station.

1.

2.

3.

4.

5.

Start the JLIP Video Capture software.

The "JLIP Initialization" screen automatically appears.

Select "COM Port".

•COM1 through COM4 ports are available. Check to see which COM port is connected to the JLIP Video Capture Docking Station and select it.

Select "Transfer Rate". •Normally select 38400.

•38400 may not be available on some computers. When transmission errors take place during use, switch to 19200 or 9600. Image data transmission will be slower at these speeds.

Click "OK" . Call up the "JLIP Initialization" window and check the connected units.

JLIP Initialization
COM Port	COM 1

Transfer Rate

38400

OK

Cancel

NOTE : If you want to change a unit or COM port or Transfer Rate, select "Initialize" from "Set-up" in the menu bar to call up the "JLIP Initialization" window. Repeat this setting procedure.

If a connection is incorrect, a connected unit is not turned on, or the connection ID numbers overlap, the message "Connection error" appears. Click "OK" to return to the Main desktop.

Image 17

Contents GV-DS1 It is recommended that you Dear CustomerSafety Precautions Do not place the Video Capture Docking Station CAU T IonsAC Power Adapter/Charger How to handle a CD-ROMMaintenance HOW to Open the Program Major Features Controls and ConnectorsHOW to Close the Program HOW the Desktop Works Picture Format SettingJlip Player Software Troubleshooting Major Specifications IndexGetting Started Advanced OperationsBusiness presentations Major FeaturesInternet homepage Video journal and postcardsVideo Capture Facility Jlip Video Capture SoftwareJlip Player Software Jlip Control Facility Data Sharing with the Video Capture SoftwareContro L S AN D Connec Tors S2 Video output jack Outputs the S-VIDEO signal Connections W hen Using JL IP Video Capture Software Input What is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation HO W to Open the PRO GramSelect Transfer Rate. Normally select Initializing JlipSelect Units Click Exit from File in the menu bar. The programme closes HOW to Close the ProgramControl buttons Main Desktop WindowMenu bar Image display area Menu BARExit Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowIndex image data is transferred to the computer Step by Step CaptureFull image data is transferred to the computer Repeat steps 2 through 5 as requiredAutomatic Capture Ideo CA PtureProgram Capture SelectOK. Program Capture and clickTransfer Automatically Interval CaptureSave the Full Image Data SavingSelecting a Picture Format Capture ModePicture Data Format Change ID Delete Index Image and Full ImageID Change InitializeCounter Value Change Counter ResetModify Capture Point window appears TransferredCreate NEW Folder Open IndexOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen JLIPjlp File window is displayed Using Jlip Player Software DataMake sure all units are properly connected p Save As Jlip jlp File window is displayed HOW to Store Jlip Player Software DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Icon button Title barDisplay File nameElapsed Time MemoOperating camcorder Setting in/out pointsBasic Oper AT Ions Start Playback Select SceneClick Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data BA SIC OP E RationsOpening a saved file Designatecopied Scene to be Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Print buttonPosition button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneVideo Printer window closes Movie Player window closes Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationAdvan CED Oper AT Ions Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAdvanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1