JVC LYT0002-0J9A, 0397MKVUNVP manual Ideo CA Pture, Automatic Capture, Program Capture

Page 26

26VIDEOCAPTURE (cont.)

AUTOMATIC CAPTURE

Automatic video capture is available only when a JLIP-compatible video source unit is con- nected. There are two types of automatic capture: Program mode and Interval mode. You can save time in either mode because, once the initial settings have been stored or you have decided what pictures to capture, the subsequent capture process is carried out automatically.

PROGRAM CAPTURE

In the Program Capture mode, select the images you want to capture, and the JLIP Video Capture Docking Station will automatically capture and transfer the images to your computer.

	Set-up
	Capture Mode	Step by Step
	Capture Mode	Step by Step
	Image Format	Automatic
	Device Change
	Initialize
	ID Change
	Counter Reset

Preparation

•Make sure all units are properly connected (☞ p. 12).

•Insert a tape into the video source unit. Click "Image Format" in "Set-up" and select "Field Picture" in the Capture Mode

(☞ p. 30).

1 Open the menu bar and click "Setup" — "Capture Mode" — "Automatic".

•The "Automatic Transfer" window appears.

2 Select data to be transferred.

•When you select "Index Image", index image data (80 x 60 pixels) is trans- ferred to your computer.

•When you select "Index & Full Image", both the index image data (80 x 60 pixels) and full image data (768 x 552 pixels) are transferred to the computer.

3 Select"OK". "Program Capture" and click

NOTES:

•Before transferring your images, make sure that enough space is available on your hard disk. For full image data space requirements, ☞ p. 24.

•When transferring full image data using the Bitmap image format (9.bmp), the transfer takes a very long time, causing the video source unit to stop playback automatically.

Image 26

Contents GV-DS1 Dear Customer It is recommended that youSafety Precautions CAU T Ions Do not place the Video Capture Docking StationAC Power Adapter/Charger How to handle a CD-ROMMaintenance HOW to Close the Program HOW the Desktop Works Major Features Controls and ConnectorsHOW to Open the Program Picture Format SettingGetting Started Troubleshooting Major Specifications IndexJlip Player Software Advanced OperationsInternet homepage Major FeaturesBusiness presentations Video journal and postcardsJlip Player Software Jlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Data Sharing with the Video Capture SoftwareContro L S AN D Connec Tors S2 Video output jack Outputs the S-VIDEO signal Connections W hen Using JL IP Video Capture Software Input Operating Environment What is video capture software ?What is Jlip ? Connectable DevicesInstallation Procedure WindowsHO W to Open the PRO Gram PreparationInitializing Jlip Select Transfer Rate. Normally selectSelect Units HOW to Close the Program Click Exit from File in the menu bar. The programme closesControl buttons Main Desktop WindowMenu bar Menu BAR Image display areaEach pulldown menu is configured as follows ExitVCR operation window 00012312FImage data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureIndex image data is transferred to the computer Repeat steps 2 through 5 as requiredProgram Capture Ideo CA PtureAutomatic Capture SelectOK. Program Capture and clickTransfer Interval Capture AutomaticallySaving Save the Full Image DataSelecting a Picture Format Capture ModePicture Data Format ID Change Delete Index Image and Full ImageChange ID InitializeModify Capture Point window appears Counter ResetCounter Value Change TransferredOpen the menu bar and click File New Album Open IndexCreate NEW Folder Saved, you will be asked whether to save or notOpen JLIPjlp File window is displayed Using Jlip Player Software DataMake sure all units are properly connected p HOW to Store Jlip Player Software Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Display Title barIcon button File nameMemo Elapsed TimeOperating camcorder Setting in/out pointsBasic Oper AT Ions Click Start Select SceneStart Playback Only the camcorder movesPrepare NEW Tape Basic OP Eration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveCorrecting and cutting the programmed counter data BA SIC OP E RationsOpening a saved file Store Designated Scene in Memory Overwriting the fileDesignatecopied Scene to be Designate Scene to be TransferredStore button Position button Power buttonIcon button Print buttonMULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesTo Print Captured Video Data with Video Printer Auto CapturePreparation Load the tape into the video unitTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationAdvan CED Oper AT Ions When Using the Video Capture Software Access Name Change Dialog BOXAccess Device Selection Dialog BOX Enter NEW Name SET NEW NameEnter Value Access Pause Time CORREC- Tion Dialog BOXAdvanc ED Operat Ions Determine ValuePower on all devices System Communication error Error - This application willThat power is on Check devices - ConfirmAjor Speci Ficat Ions Change ID COM Port Setup MenuAutomatic Capture Auto Bitmap Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1