JVC 0397MKV*UN*VP manual Error - This application will, Check devices - Confirm, That power is on

Page 65

TROUBLESHOOTING 65

MESSAGE

⬤ POSSIBLE CAUSE

⬛ CORRECTIVE ACTION

 

 

 

Error – – This application will

⬤ The COM port used for the JLIP connector is not

close.

selected, or the COM port is selected but the

Check devices – – Confirm

connection is wrong.

that power is ON.

⬛ Check the connected COM port and select it on the

 

"Serial Port Selection" screen (☞ pg. 46).

 

 

No devices detected to

⬤ Power is not supplied or the connection is wrong.

connect.

⬛ Connect the devices correctly and turn them on

Power ON all devices in

(☞ pg. 42, 43).

system.

 

 

 

Communication error

⬤ Device is not turned on or cable is disconnected.

(&H (number))

⬛ Connect the device correctly and turn it on

Check cable connection.

(☞ pg. 42, 43).

 

⬛ If device was turned off and on again during

 

operation, click "OK". All devices should function

 

properly.

 

 

Select the device to control.

⬤ The line where the name of the device to use

 

appears is not clicked.

 

⬛ Click on it and "OK" (☞ pg. 47).

 

 

No video cassette!!

⬤ The video cassette is not loaded in the camcorder.

Load a video cassette to ID

When the video cassette is removed during

(number).

operation, this message appears.

 

⬛ Insert the video cassette into the camcorder.

 

 

Invalid entry in scene

⬤ The value of the CUT OUT point is smaller than

(number) (There is IN > OUT

the CUT IN point's.

condition). Correct the time

⬛ Set the value of the CUT OUT point so that it is

or delete the scene.

larger than the CUT IN point's (☞ pgs. 50, 54).

 

 

Select a number between 0

⬤ When correcting the CUT IN/OUT points, the

and 24.

value you set differs from the original by over 25

 

frames.

 

⬛ Select integral number from 0 to 24 (☞ pg. 54).

 

 

Invalid frame number on drop

⬤ Because the DV-format digital camcorder uses the

frame counter.

drop frame system, inputting frame 00 and 01 is

 

impossible.

 

⬛ Input frame value other than 00 or 01

 

(☞ pgs. 48, 54).

 

 

The monitor displays of the application software illustrated in this manual may differ from those you are actually viewing depending on the operating environment of your computer.

Page 64 Page 66
Image 65
Page 64 Page 66
Contents GV-DS1 It is recommended that you Dear CustomerSafety Precautions Do not place the Video Capture Docking Station CAU T IonsAC Power Adapter/Charger How to handle a CD-ROMMaintenance HOW to Open the Program Major Features Controls and ConnectorsHOW to Close the Program HOW the Desktop Works Picture Format SettingJlip Player Software Troubleshooting Major Specifications IndexGetting Started Advanced OperationsBusiness presentations Major FeaturesInternet homepage Video journal and postcardsVideo Capture Facility Jlip Video Capture SoftwareJlip Player Software Jlip Control Facility Data Sharing with the Video Capture SoftwareContro L S AN D Connec Tors S2 Video output jack Outputs the S-VIDEO signal Connections W hen Using JL IP Video Capture Software Input What is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation HO W to Open the PRO GramSelect Transfer Rate. Normally select Initializing JlipSelect Units Click Exit from File in the menu bar. The programme closes HOW to Close the ProgramControl buttons Main Desktop WindowMenu bar Image display area Menu BARExit Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowIndex image data is transferred to the computer Step by Step CaptureFull image data is transferred to the computer Repeat steps 2 through 5 as requiredAutomatic Capture Ideo CA PtureProgram Capture SelectOK. Program Capture and clickTransfer Automatically Interval CaptureSave the Full Image Data SavingSelecting a Picture Format Capture ModePicture Data Format Change ID Delete Index Image and Full ImageID Change InitializeCounter Value Change Counter ResetModify Capture Point window appears TransferredCreate NEW Folder Open IndexOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen JLIPjlp File window is displayed Using Jlip Player Software DataMake sure all units are properly connected p Save As Jlip jlp File window is displayed HOW to Store Jlip Player Software DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Icon button Title barDisplay File nameElapsed Time MemoOperating camcorder Setting in/out pointsBasic Oper AT Ions Start Playback Select SceneClick Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data BA SIC OP E RationsOpening a saved file Designatecopied Scene to be Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Print buttonPosition button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneVideo Printer window closes Movie Player window closes Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationAdvan CED Oper AT Ions Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAdvanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1
Top Page Image Contents