JVC LYT0002-0J9A, 0397MKV*UN*VP manual Connections When Using Jlip Playe r Soft ware

Page 42

42

CONNECTIONS(WhenUsingJLIPPlayerSoftware)

WHEN CONNECTING TO A VIDEO SOURCE UNIT WITH JLIP CONNECTOR OR TO A VIDEO PRINTER

Be sure to turn off the power of all connected units before making any connections.

When connecting the provided cable, be sure to connect the plug with the Core Filter to the Video Capture Docking Station.

To COM port

 

 

To digital

 

 

connector

(RS-232C)

 

 

(8 pin)

PC connection

Core

Filter

cable (provided)

 

PC

3.5 mm diameter

4-pole cable (provided)

When connected with the Video Printer

GV-PT2 Video Printer

Connect this if the video unit

To JLIP connector has an S-Video input connector

To S-Video input connector

To video input connector

S-Video cable

If you edit using a non-JVC VCR...

T W

It is possible to use the remote control unit provided with the GR-DVM1. Also refer to the GR-DVM1’s instructions on connection and operation with your brand of VCR.

NOTE:

Some VCR brands or models cannot be operated.

RM-V708U or RM-V710U

Image 42
Contents GV-DS1 Dear Customer It is recommended that youSafety Precautions CAU T Ions Do not place the Video Capture Docking StationHow to handle a CD-ROM MaintenanceAC Power Adapter/Charger HOW to Close the Program HOW the Desktop Works Major Features Controls and ConnectorsHOW to Open the Program Picture Format SettingGetting Started Troubleshooting Major Specifications IndexJlip Player Software Advanced OperationsInternet homepage Major FeaturesBusiness presentations Video journal and postcardsJlip Player Software Jlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Data Sharing with the Video Capture SoftwareContro L S AN D Connec Tors S2 Video output jack Outputs the S-VIDEO signal Connections W hen Using JL IP Video Capture Software Input Operating Environment What is video capture software ?What is Jlip ? Connectable DevicesInstallation Procedure WindowsHO W to Open the PRO Gram PreparationInitializing Jlip Select Transfer Rate. Normally selectSelect Units HOW to Close the Program Click Exit from File in the menu bar. The programme closesMain Desktop Window Menu barControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows ExitVCR operation window 00012312FImage data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureIndex image data is transferred to the computer Repeat steps 2 through 5 as requiredProgram Capture Ideo CA PtureAutomatic Capture SelectOK. Program Capture and clickTransfer Interval Capture AutomaticallySaving Save the Full Image DataCapture Mode Picture Data FormatSelecting a Picture Format ID Change Delete Index Image and Full ImageChange ID InitializeModify Capture Point window appears Counter ResetCounter Value Change TransferredOpen the menu bar and click File New Album Open IndexCreate NEW Folder Saved, you will be asked whether to save or notUsing Jlip Player Software Data Make sure all units are properly connected pOpen JLIPjlp File window is displayed HOW to Store Jlip Player Software Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software Starting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices Display Title barIcon button File nameMemo Elapsed TimeSetting in/out points Basic Oper AT IonsOperating camcorder Click Start Select SceneStart Playback Only the camcorder movesPrepare NEW Tape Basic OP Eration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveBA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Store Designated Scene in Memory Overwriting the fileDesignatecopied Scene to be Designate Scene to be TransferredStore button Position button Power buttonIcon button Print buttonMULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesTo Print Captured Video Data with Video Printer Auto CapturePreparation Load the tape into the video unitTo print only the cut-in scene on the edited tape Connecting other device during operation Advan CED Oper AT IonsChanging ID number When Using the Video Capture Software Access Name Change Dialog BOXAccess Device Selection Dialog BOX Enter NEW Name SET NEW NameEnter Value Access Pause Time CORREC- Tion Dialog BOXAdvanc ED Operat Ions Determine ValuePower on all devices System Communication error Error - This application willThat power is on Check devices - ConfirmAjor Speci Ficat Ions Change ID COM Port Setup MenuAutomatic Capture Auto Bitmap Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1