JVC 0397MKVUNVP, LYT0002-0J9A manual Select Devices

Page 47

47

	Device Selection
	Select device to control.
	VCR
	DISCONNECT	OK
	06:VCRCAMERA	OK
	06:VCRCAMERA
		CANCEL
	VIDEO PRINTER
	DISCONNECT
		4

•An error message "No devices detected to connect. Power ON all devices in system." appears . . .

... when a wrong port number is selected.

... when the connection is wrong.

... when the device's ID number is already in use.

... when the device's power is not turned on.

Check the Serial Port selection, too.

To return to step 1, check the connection and the device's power and try again.

•When all serial COM ports are occupied by other applications the error message "Error--This application will close. Check devices--Confirm that power is ON." appears. Free a serial COM port to start up JLIP Player Software.

SELECT DEVICE(S)

Click on the name of the device you wish to control. Clicking "OK" brings up the MOVIE PLAYER window.

•It is possible to select a second device of a different type simultaneously, but it is impossible to select two same type devices simultaneously.

Image 47

Contents GV-DS1 It is recommended that you Dear CustomerSafety Precautions Do not place the Video Capture Docking Station CAU T IonsAC Power Adapter/Charger How to handle a CD-ROMMaintenance Picture Format Setting Major Features Controls and ConnectorsHOW to Open the Program HOW to Close the Program HOW the Desktop WorksAdvanced Operations Troubleshooting Major Specifications IndexJlip Player Software Getting StartedVideo journal and postcards Major FeaturesBusiness presentations Internet homepageData Sharing with the Video Capture Software Jlip Video Capture SoftwareVideo Capture Facility Jlip Player Software Jlip Control FacilityContro L S AN D Connec Tors S2 Video output jack Outputs the S-VIDEO signal Connections W hen Using JL IP Video Capture Software Input Connectable Devices What is video capture software ?What is Jlip ? Operating EnvironmentWindows Installation ProcedurePreparation HO W to Open the PRO GramSelect Transfer Rate. Normally select Initializing JlipSelect Units Click Exit from File in the menu bar. The programme closes HOW to Close the ProgramControl buttons Main Desktop WindowMenu bar Image display area Menu BARExit Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureIndex image data is transferred to the computer Full image data is transferred to the computerSelectOK. Program Capture and click Ideo CA PtureAutomatic Capture Program CaptureTransfer Automatically Interval CaptureSave the Full Image Data SavingSelecting a Picture Format Capture ModePicture Data Format Initialize Delete Index Image and Full ImageChange ID ID ChangeTransferred Counter ResetCounter Value Change Modify Capture Point window appearsSaved, you will be asked whether to save or not Open IndexCreate NEW Folder Open the menu bar and click File New AlbumOpen JLIPjlp File window is displayed Using Jlip Player Software DataMake sure all units are properly connected p Save As Jlip jlp File window is displayed HOW to Store Jlip Player Software DataProblem Cause With the desired counter Counter cannot be resetWhere the program run file Cannot capture video dataMessage Appears when Action Not enough disk ErrorExecute after Playing backMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software Select Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices File name Title barIcon button DisplayElapsed Time MemoOperating camcorder Setting in/out pointsBasic Oper AT Ions Only the camcorder moves Select SceneStart Playback Click StartStart Editing Basic OP Eration SDubbing Prepare NEW TapeSelect Floppy Disk Drive Start SavingEnter File Name Save FileCorrecting and cutting the programmed counter data BA SIC OP E RationsOpening a saved file Designate Scene to be Transferred Overwriting the fileDesignatecopied Scene to be Store Designated Scene in MemoryPrint button Position button Power buttonIcon button Store buttonStrobe Speed button Content buttonPosition button MULTI-PIX buttonStore Scene PrintingBring UP Video Printer Window PlaybackVideo Printer window closes Movie Player window closes Click Close Choose Exit from FileLoad the tape into the video unit Auto CapturePreparation To Print Captured Video Data with Video PrinterTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationAdvan CED Oper AT Ions Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX When Using the Video Capture SoftwareDetermine Value Access Pause Time CORREC- Tion Dialog BOXAdvanc ED Operat Ions Enter ValueCheck devices - Confirm Error - This application willThat power is on Power on all devices System Communication errorAjor Speci Ficat Ions Delete Index Image and Full Image Desktop Window Pg , 48 Setup MenuAutomatic Capture Auto Bitmap Change ID COM PortGV-DS1