JVC LYT0002-0J9A, 0397MKV*UN*VP manual Image data flow, Capturing Video Images

Page 24

24

VIDEOCAPTURE

CAPTURING VIDEO IMAGES

There are three capture modes available: Step by Step, Program and Interval. The latter two modes are available only when connected to a JLIP compatible video source unit. Step by Step Capture mode must be used to capture images from a video source unit with no JLIP connector.

Image data flow

Video source

unit

Video signal

GV-DS1

 

 

 

 

(Image stored in video memory)

 

 

 

Full image data

(with a resolution of 768 x 552 pixels)

2 types of video data

Bitmap data Approx. 1.3MB

JPEG video compression data Approx. 50 kB

Index image data (with a resolution of 80 x 60 pixels)

PC

(video data are stored on a hard disk or the like)

When storing full image data on a 2HD disk,

An image saved in the bitmap data format can be stored on one disk.

About 28 images saved in the JPEG video compression format can be stored on one disk. This is the case when using floppy disks formatted for 1.44 MB.

NOTES:

•The index image is displayed in the image display box.

•Each time the image display box is double-clicked, the full image data (768 x 552 pixels) is displayed only after full image data transfer is finished.

Image 24
Contents GV-DS1 Dear Customer It is recommended that youSafety Precautions CAU T Ions Do not place the Video Capture Docking StationHow to handle a CD-ROM MaintenanceAC Power Adapter/Charger Major Features Controls and Connectors HOW to Open the ProgramHOW to Close the Program HOW the Desktop Works Picture Format SettingTroubleshooting Major Specifications Index Jlip Player SoftwareGetting Started Advanced OperationsMajor Features Business presentationsInternet homepage Video journal and postcardsJlip Video Capture Software Video Capture FacilityJlip Player Software Jlip Control Facility Data Sharing with the Video Capture SoftwareContro L S AN D Connec Tors S2 Video output jack Outputs the S-VIDEO signal Connections W hen Using JL IP Video Capture Software Input What is video capture software ? What is Jlip ?Operating Environment Connectable DevicesInstallation Procedure WindowsHO W to Open the PRO Gram PreparationInitializing Jlip Select Transfer Rate. Normally selectSelect Units HOW to Close the Program Click Exit from File in the menu bar. The programme closesMain Desktop Window Menu barControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows ExitVCR operation window 00012312FImage data flow Capturing Video ImagesStep by Step Capture Index image data is transferred to the computerFull image data is transferred to the computer Repeat steps 2 through 5 as requiredIdeo CA Pture Automatic CaptureProgram Capture SelectOK. Program Capture and clickTransfer Interval Capture AutomaticallySaving Save the Full Image DataCapture Mode Picture Data FormatSelecting a Picture Format Delete Index Image and Full Image Change IDID Change InitializeCounter Reset Counter Value ChangeModify Capture Point window appears TransferredOpen Index Create NEW FolderOpen the menu bar and click File New Album Saved, you will be asked whether to save or notUsing Jlip Player Software Data Make sure all units are properly connected pOpen JLIPjlp File window is displayed HOW to Store Jlip Player Software Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskMemo Jlip Player Software Section Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software Starting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices Title bar Icon buttonDisplay File nameMemo Elapsed TimeSetting in/out points Basic Oper AT IonsOperating camcorder Select Scene Start PlaybackClick Start Only the camcorder movesBasic OP Eration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveBA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Overwriting the file Designatecopied Scene to beStore Designated Scene in Memory Designate Scene to be TransferredPosition button Power button Icon buttonStore button Print buttonContent button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesAuto Capture PreparationTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Connecting other device during operation Advan CED Oper AT IonsChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAccess Pause Time CORREC- Tion Dialog BOX Advanc ED Operat IonsEnter Value Determine ValueError - This application will That power is onPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Setup Menu Automatic Capture Auto BitmapChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1