Foxconn manual Installation, Typical Application of a 7870 Interfacility Link

Page 15

2 Installation

Chapter 2 describes how to install the 7870 Interfacility Link units. Setting up the 7870E Transmitter/Receiver consists of:

2.1 Setting up the Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 Connecting the Fiber Optic Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.3 Setting Up the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.4 Powering the IFL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4.1 7180M Chassis

12

2.5 Connecting the Back Panel Jumpers . . . . . . . . . . . . . . . . . . . . . . . 13 2.6 Aligning the Fiber Optic Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Observe all warnings and cautions mentioned at the beginning of this manual (See Important Information on page iii).

If after set-up you experience problems, see Chapter 4 Troubleshooting on page 25.

Figure 6 Typical Application of a 7870 Interfacility Link

7870 Interfacility Link Installation and User’s Guide	page 7
Foxcom proprietary information

Image 15

Contents Copyright Interfacility Link Installation and User’s GuideMailsales@foxcom.com Table of Contents Figures Important Information Warranty and Repair PolicyGeneral Warranty Specific Product Warranty InstructionsLimitations of Liabilities ReturnsReporting Defects PrecautionsPersonal Safety Equipment SafetyImportant Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block DiagramsOption Label Options7870T Transmitter Front and Rear Panel Product DrawingsPanel Descriptions LED Name LED Function LaserLED Name LED Function Opt 7870Transmitter Block Diagram Block DiagramsBlock Diagrams Typical Application of a 7870 Interfacility Link InstallationSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M ChassisJumper Installation Tx and Rx only Connecting the Back Panel JumpersJumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment SetupDocument no -005-35-C5 RF Specifications Product SpecificationsPhysical Specifications Optical SpecificationsUnit dimensions Model Dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperativePin No Function Name Slot No 7180M Alarm Connector J12 Pinouts3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function NameProblem Possible Cause TroubleshootingMay still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic ConnectionsWiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC ConnectorsAppendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel LabelAppendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel LabelAppendix Adapter Pinouts Pin Number FunctionSlot Number 2380 Pin Number Pin # Function Name Slot NoAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5