Foxconn 7870 manual Optical Specifications, Physical Specifications

Page 26

3.1 7870 Interfacility Link Specifications

	Optical Specifications
	Optical Wavelength	1310 ± 10 nm
	Optical power output	0.5 mW/-2 dBm [minimum]
	Optical connector	FC/APC
	Optical budget / distance	16 dB / 40 Km
	Optical return loss	-60 dB
	Optical connector loss	0.5 dB/mated pair
	Physical Specifications
	Chassis capacity	8 plug-ins, and 2 power supplies
	Chassis size	19” × 3U × 7”
	Power for rackmount [max.]	100 to 240 VAC 50/60Hz 90 Watts
	Standalone size	5” × 4.8” × 1.3”
	Power for standalone
	Transmitter	+14 VDC @ 200 mA max.
	Transmitter	[300 mA temp.< 10° C)
		[300 mA temp.< 10° C)
	Receiver	+14VDC @ 250 mA max.
	Operating Temperature Range	-10°C to +55°C
	Storage Temperature Range	-40°C to +85°C

All specifications are subject to change without prior notice

Note If the link is between 100 - 500 meters, foxcom technicians will limit the output power to +2 dBm/1.6 mW. This information must be given to Foxcom when ordering the link.

page 18

Document no. 93-005-35-C5

Image 26

Contents Interfacility Link Installation and User’s Guide CopyrightMailsales@foxcom.com Table of Contents Figures Specific Product Warranty Instructions Warranty and Repair PolicyGeneral Warranty Important InformationReturns Limitations of LiabilitiesEquipment Safety PrecautionsPersonal Safety Reporting DefectsImportant Information Options Product Drawings Panel Descriptions Block Diagrams Introduction to the 7870 Interfacility LinkOptions Option LabelProduct Drawings 7870T Transmitter Front and Rear PanelLED Name LED Function Opt Panel DescriptionsLED Name LED Function Laser Block Diagrams 7870Transmitter Block DiagramBlock Diagrams Installation Typical Application of a 7870 Interfacility LinkSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 1 7180M Chassis 7180M Chassis Rear ViewConnecting the Back Panel Jumpers Jumper Installation Tx and Rx onlyJumper Installation 2040 Switch in slots 2 Fiber Optic Alignment Setup Aligning the Fiber Optic LinkDocument no -005-35-C5 Product Specifications RF SpecificationsOptical Specifications Physical SpecificationsModel Dimensions Unit dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7870 the J11 connector is inoperative 7180M Chassis Pinouts7180M Alarm Connector J12 Pinouts Pin No Function Name Slot No2 7180M Monitor Connector Pinout J13 Pin # Function Name 3 7180M and Redundancy SwitchingTroubleshooting Problem Possible CauseMay still function without LED Appendix 1 Cleaning Fiber Optic Connections Description ManufacturerAppendix 1.1 Cleaning Procedures for FC/APC Connectors Wiping the connector with a Kim wiperAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead PortsAppendix 1.2.1 Swab Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 2380 Dimensions and Front Panel Label Appendix 3 The 2380 Relay AdapterAppendix 3.1.2 Mounting the the 2380 Relay Adapter Appendix 3.1 Installing the 2380 Relay AdapterAppendix 3.1.1 Parts Required for Installing Mounting the Screws Appendix 3.2 2380 Dimensions and Front Panel Label 2380 DimensionsSlot Number Appendix Adapter PinoutsPin Number Function Pin # Function Name Slot No 2380 Pin NumberAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5