Foxconn 7870 manual Appendix 2 Installing a Standalone Unit

Page 39

Appendix 2 Installing a Standalone Unit

To install the 7870T-STD or 7870R--STD Standalone:

1.Place the 7870 unit on the standalone flange, matching the holes.

2.Using four screws (#4 or #6) secure the unit and the flange to the wall.

3.Apply AC power to the standalone power supply unit.

4.Connect the 7870 unit to the power supply. The Laser LED should be lit.

All remaining steps are the same as in the product manual. See sections 2.1 Setting up the Transmitter on page8 and 2.3 Setting Up the Receiver on page10.

7870 Interfacility Link Installation and User’s Guide

page 31

Foxcom proprietary information

 

Image 39
Contents Copyright Interfacility Link Installation and User’s GuideMailsales@foxcom.com Table of Contents Figures Important Information Warranty and Repair PolicyGeneral Warranty Specific Product Warranty InstructionsLimitations of Liabilities ReturnsReporting Defects PrecautionsPersonal Safety Equipment SafetyImportant Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block DiagramsOption Label Options7870T Transmitter Front and Rear Panel Product DrawingsPanel Descriptions LED Name LED Function LaserLED Name LED Function Opt 7870Transmitter Block Diagram Block DiagramsBlock Diagrams Typical Application of a 7870 Interfacility Link InstallationSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M ChassisJumper Installation Tx and Rx only Connecting the Back Panel JumpersJumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment SetupDocument no -005-35-C5 RF Specifications Product SpecificationsPhysical Specifications Optical SpecificationsUnit dimensions Model Dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperativePin No Function Name Slot No 7180M Alarm Connector J12 Pinouts3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function NameProblem Possible Cause TroubleshootingMay still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic ConnectionsWiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC ConnectorsAppendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel LabelAppendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel LabelAppendix Adapter Pinouts Pin Number FunctionSlot Number 2380 Pin Number Pin # Function Name Slot NoAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5