Foxconn 7870 manual Appendix Adapter Pinouts, Pin Number Function, Slot Number

Page 45

Appendix 3.3 2380 Adapter Pinouts

Appendix 3.3		2380 Adapter Pinouts
	Table 11 2380 Alarms Pinouts [J2]

	Pin Number		Function		Name	Slot Number
		1	Alarm		NOP1	1
		2	Alarm		COM1	1
		3	Alarm		NOP2	2
		4	Alarm		COM2	2
		5	Alarm		NOP3	3
		6	Alarm		COM3	3
		7	Alarm		NOP4	4
		8	Alarm		COM4	4
		9	Alarm		NOP5	5
		10	Alarm		COM5	5
		11	Alarm		NOP6	6
		12	Alarm		COM6	6
		13	Alarm		NOP7	7
		14	Alarm		COM7	7
		15	Alarm		NOP8	8
		16	Alarm		COM8	8
		17
		18
		19
		20
		21
		22
		23	Main PS Alarm		MPSA
		24	Standby PS Alarm		SPSA
		25	Power Supply Comm.		PSCOM

Note Alarms in Pins 1 through 16 function if there is either an RF or Optical signals failure.

7870 Interfacility Link Installation and User’s Guide	page 37
Foxcom proprietary information

Image 45

Contents Copyright Interfacility Link Installation and User’s GuideMailsales@foxcom.com Table of Contents Figures General Warranty Warranty and Repair PolicySpecific Product Warranty Instructions Important InformationLimitations of Liabilities ReturnsPersonal Safety PrecautionsEquipment Safety Reporting DefectsImportant Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block DiagramsOption Label Options7870T Transmitter Front and Rear Panel Product DrawingsPanel Descriptions LED Name LED Function LaserLED Name LED Function Opt 7870Transmitter Block Diagram Block DiagramsBlock Diagrams Typical Application of a 7870 Interfacility Link InstallationSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M ChassisJumper Installation Tx and Rx only Connecting the Back Panel JumpersJumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment SetupDocument no -005-35-C5 RF Specifications Product SpecificationsPhysical Specifications Optical SpecificationsUnit dimensions Model Dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperativePin No Function Name Slot No 7180M Alarm Connector J12 Pinouts3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function NameProblem Possible Cause TroubleshootingMay still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic ConnectionsWiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC ConnectorsAppendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel LabelAppendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel LabelAppendix Adapter Pinouts Pin Number FunctionSlot Number 2380 Pin Number Pin # Function Name Slot NoAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5