Foxconn 7870 manual Table of Contents

Page 3

Table of Contents

 

Important Information

iii

Chapter 1 Introduction to the 7870 Interfacility Link

1

1.1

Options

.2

1.2

Product Drawings

.3

1.3

Panel Descriptions

.4

1.4

Block Diagrams

.5

Chapter 2 Installation

7

2.1

Setting up the Transmitter

.8

2.2

Connecting the Fiber Optic Cable

.9

2.3

Setting Up the Receiver

10

2.4

Powering the IFL

11

2.4.1

7180M Chassis

12

2.5

Connecting the Back Panel Jumpers

13

2.6

Aligning the Fiber Optic Link

15

Chapter 3 Product Specifications

17

3.1 7870 Interfacility Link Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .17

3.2 Model Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

3.3 7870 Interfacility Link Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

3.3.1 Transmitter Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.3.2 Receiver Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.4 7180M Chassis Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3.4.1 7180M Alarm Connector Pinouts [J12] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3.4.2 7180M Monitor Connector Pinout [J13]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.4.3 7180M and Redundancy Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 4 Troubleshooting

25

Appendix 1

Cleaning Fiber Optic Connections

27

Appendix 1.1 Cleaning Procedures for FC/APC Connectors

28

Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports

29

Appendix 1.2.1 Swab Method

29

Appendix 1.2.2 Compressed Air Method

29

Appendix 2

Installing a Standalone Unit

31

Appendix 3

The 2380 Relay Adapter

33

Appendix 3.1 Installing the 2380 Relay Adapter

34

Appendix 3.1.1 Parts Required for Installing the 2380

34

Appendix 3.1.2 Mounting the the 2380 Relay Adapter

34

Appendix 3.2 2380 Dimensions and Front Panel Label

36

Appendix 3.3 2380 Adapter Pinouts

37

Appendix 4

Pinout Charts and Diagrams

39

7870 Interfacility Link Installation and User’s Guide

page i

Foxcom proprietary information

 

Image 3
Contents Copyright Interfacility Link Installation and User’s GuideMailsales@foxcom.com Table of Contents Figures Important Information Warranty and Repair PolicyGeneral Warranty Specific Product Warranty InstructionsLimitations of Liabilities ReturnsReporting Defects PrecautionsPersonal Safety Equipment SafetyImportant Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block DiagramsOption Label Options7870T Transmitter Front and Rear Panel Product DrawingsPanel Descriptions LED Name LED Function LaserLED Name LED Function Opt 7870Transmitter Block Diagram Block DiagramsBlock Diagrams Typical Application of a 7870 Interfacility Link InstallationSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M ChassisJumper Installation Tx and Rx only Connecting the Back Panel JumpersJumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment SetupDocument no -005-35-C5 RF Specifications Product SpecificationsPhysical Specifications Optical SpecificationsUnit dimensions Model Dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperativePin No Function Name Slot No 7180M Alarm Connector J12 Pinouts3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function NameProblem Possible Cause TroubleshootingMay still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic ConnectionsWiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC ConnectorsAppendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel LabelAppendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel LabelAppendix Adapter Pinouts Pin Number FunctionSlot Number 2380 Pin Number Pin # Function Name Slot NoAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5