Foxconn 7870 manual Returns, Limitations of Liabilities

Page 6

Important Information

Returns

In the event that it is necessary to return any product against above warranty, the following procedure shall be followed:

1.Return authorization is to be received from Foxcom prior to returning any unit. Advise Foxcom of the model, serial number, and discrepancy. The unit may then be forwarded to Foxcom, transportation prepaid. Devices returned collect or without authorization may not be accepted.

2.Prior to repair, Foxcom will advise the customer of our test results and any charges for repairing customer-caused problems or out-of-warranty conditions etc.

3.Repaired products are warranted for the balance of the original warranty period, or at least 90 days from date of shipment.

Limitations of Liabilities

Foxcom's liability on any claim, of any kind, including negligence for any loss or damage arising from, connected with, or resulting from the purchase order, contract, quotation, or from the performance or breach thereof, or from the design, manufacture, sale, delivery, installation, inspection, operation or use of any equipment covered by or furnished under this contact, shall in no case exceed the purchase price of the device which gives rise to the claim.

EXCEPT AS EXPRESSLY PROVIDED HEREIN, FOXCOM MAKES NO WARRANTY, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY GOODS, PARTS AND SERVICES PROVIDED IN CONNECTION WITH THIS AGREEMENT INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FOXCOM SHALL NOT BE LIABLE FOR ANY OTHER DAMAGE INCLUDING, BUT NOT LIMITED TO, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH FURNISHING OF GOODS, PARTS AND SERVICE HEREUNDER, OR THE PERFORMANCE, USE OF, OR INABILITY TO USE THE GOODS, PARTS AND SERVICE.

The Company's exclusive warranty and the remedy provided for breach thereof shall not apply to:

1.Any Product used or operated other than pursuant to the Company's written instructions,

2.Damage or deficiencies resulting from accident, alteration, modification, misuse, tampering, negligence, improper maintenance, installation or abuse,

3.Use of any Product other than at the Installation Site,

4.Use of any Product that is defective or damaged due to misuse, accident, or neglect, or due to external electrical stress, lightning or other acts of nature,

5.Use of any Product by a person who is not any authorized employee of the Customer, or

6.Used other than as explicitly authorized in writing by the Company.

page iv

Document no. 93-005-35-C5

Image 6
Contents Interfacility Link Installation and User’s Guide CopyrightMailsales@foxcom.com Table of Contents Figures Specific Product Warranty Instructions Warranty and Repair PolicyGeneral Warranty Important InformationReturns Limitations of LiabilitiesEquipment Safety PrecautionsPersonal Safety Reporting DefectsImportant Information Options Product Drawings Panel Descriptions Block Diagrams Introduction to the 7870 Interfacility LinkOptions Option LabelProduct Drawings 7870T Transmitter Front and Rear PanelPanel Descriptions LED Name LED Function LaserLED Name LED Function Opt Block Diagrams 7870Transmitter Block DiagramBlock Diagrams Installation Typical Application of a 7870 Interfacility LinkSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 1 7180M Chassis 7180M Chassis Rear ViewConnecting the Back Panel Jumpers Jumper Installation Tx and Rx onlyJumper Installation 2040 Switch in slots 2 Fiber Optic Alignment Setup Aligning the Fiber Optic LinkDocument no -005-35-C5 Product Specifications RF SpecificationsOptical Specifications Physical SpecificationsModel Dimensions Unit dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7870 the J11 connector is inoperative 7180M Chassis Pinouts7180M Alarm Connector J12 Pinouts Pin No Function Name Slot No2 7180M Monitor Connector Pinout J13 Pin # Function Name 3 7180M and Redundancy SwitchingTroubleshooting Problem Possible CauseMay still function without LED Appendix 1 Cleaning Fiber Optic Connections Description ManufacturerAppendix 1.1 Cleaning Procedures for FC/APC Connectors Wiping the connector with a Kim wiperAppendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 1.2.1 Swab MethodAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 2380 Dimensions and Front Panel Label Appendix 3 The 2380 Relay AdapterAppendix 3.1 Installing the 2380 Relay Adapter Appendix 3.1.1 Parts Required for InstallingAppendix 3.1.2 Mounting the the 2380 Relay Adapter Mounting the Screws Appendix 3.2 2380 Dimensions and Front Panel Label 2380 DimensionsAppendix Adapter Pinouts Pin Number FunctionSlot Number Pin # Function Name Slot No 2380 Pin NumberAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5