Foxconn 7870 manual Connecting the Fiber Optic Cable

Page 17

2.2 Connecting the Fiber Optic Cable

2.2Connecting the Fiber Optic Cable

Before connecting the cable:

1.The fiber optic cable must be either fusion spliced or connected via FC/APC connectors.

2.Wipe the connector with a lint-free cotton cloth.

3.Note the polarity key of the optical connector before inserting.

To connect the cable:

1.Line Up the Polarity Key.

2.Insert the connector

3.Tighten the connector

Caution Do not apply any glue, silicon adhesive, or any other material to the fiber optic connector!

7870 Interfacility Link Installation and User’s Guide	page 9
Foxcom proprietary information

Image 17

Contents Copyright Interfacility Link Installation and User’s GuideMailsales@foxcom.com Table of Contents Figures General Warranty Warranty and Repair PolicySpecific Product Warranty Instructions Important InformationLimitations of Liabilities ReturnsPersonal Safety PrecautionsEquipment Safety Reporting DefectsImportant Information Introduction to the 7870 Interfacility Link Options Product Drawings Panel Descriptions Block DiagramsOption Label Options7870T Transmitter Front and Rear Panel Product DrawingsLED Name LED Function Opt Panel DescriptionsLED Name LED Function Laser 7870Transmitter Block Diagram Block DiagramsBlock Diagrams Typical Application of a 7870 Interfacility Link InstallationSetting up the Transmitter Connecting the Fiber Optic Cable Setting Up the Receiver Powering the IFL 7180M Chassis Rear View 1 7180M ChassisJumper Installation Tx and Rx only Connecting the Back Panel JumpersJumper Installation 2040 Switch in slots 2 Aligning the Fiber Optic Link Fiber Optic Alignment SetupDocument no -005-35-C5 RF Specifications Product SpecificationsPhysical Specifications Optical SpecificationsUnit dimensions Model Dimensions7870 Interfacility Link Pinouts 7870R Receiver Pinout 7180M Chassis Pinouts 7870 the J11 connector is inoperativePin No Function Name Slot No 7180M Alarm Connector J12 Pinouts3 7180M and Redundancy Switching 2 7180M Monitor Connector Pinout J13 Pin # Function NameProblem Possible Cause TroubleshootingMay still function without LED Description Manufacturer Appendix 1 Cleaning Fiber Optic ConnectionsWiping the connector with a Kim wiper Appendix 1.1 Cleaning Procedures for FC/APC ConnectorsAppendix 1.2.2 Compressed Air Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead PortsAppendix 1.2.1 Swab Method Appendix 1.2 Cleaning Procedure for FC/APC Bulkhead Ports Appendix 2 Installing a Standalone Unit Document no -005-35-C5 Appendix 3 The 2380 Relay Adapter Appendix 2380 Dimensions and Front Panel LabelAppendix 3.1.2 Mounting the the 2380 Relay Adapter Appendix 3.1 Installing the 2380 Relay AdapterAppendix 3.1.1 Parts Required for Installing Mounting the Screws 2380 Dimensions Appendix 3.2 2380 Dimensions and Front Panel LabelSlot Number Appendix Adapter PinoutsPin Number Function 2380 Pin Number Pin # Function Name Slot NoAppendix 4 Pinout Charts and Diagrams Standard 7180M and 7180M with 2380 Relay Adapter Pinout 7180M and 2040 RF Switch Pinout Pinout of 7180M Jumper with 2040 RF Switch in slots 2 Pinout of 7180M jumper with 2040 RF switch in slot Pinout of 7180M jumper with 2040 RF switch in slot Page Document no -005-35-C5