Ericsson LBI-38732E manual Scanning Conventional Channels

Page 95

will become active for voice communication after the tone sequence is complete.

Tone encode will be transmitted with Channel Guard, if one is defined, and tones are always transmitted in clear voice mode, even if the channel is set for digital or private (see VOICE MODES). Digital or private voice transmission will resume normally after the tone trans- mission.

SCANNING CONVENTIONAL CHANNELS

Channels which have been previously added to the scan list on a per system basis may be scanned. The selected channel is scanned (if enabled through pro- gramming) whether or not it is in the scan list. Each conventional system’s channel scan list is retained in memory when the radio is turned off or when the battery pack is removed.

The scan rate will vary depending upon the number of channels in the scan list and whether or not the radio is programmed to scan for channels with decoding en- abled. Fewer channels will result in a faster scan rate. If programmed for dual-priority scan operation, the priority- one, priority-two and the remaining scan list channels are scanned. Once a signal is detected and the correct encoded squelch signal is decoded (if programmed), the radio receives the message and displays the received scan channel. At the same time, scanning continues on the priority-one and priority-two channels. Should the priority-one or priority-two channel carrier, regardless of encoded squelch decoding, be detected while a non-pri- ority channel is being received, the display name is

updated, 1 or 2 comes on and the received channel is

95

Page 94 Page 96
Image 95
Page 94 Page 96
Contents LBI-38732E Operator’s Manual Page Table of Contents Edacs Trunked Mode Operation Scanning Conventional Channels Operating Rules and Regulations Safety Information Battery Charging and Care Page For Best Performance Extended Operations FCC Licensing Transceiver ServiceIntroduction User Interface RK II Portable Radio Top And Partial Left Panel Views Buttons and Knobs Page Keypad PUSH-TOTalk but TON PTTGROUP/CHANNEL Selection Page Display SYS Busy MessagesCC Scan Txemer TX Data Sysc on Frcd PVT Status IndicatorsPage Page Universal Device Connector UDC Call Originate Autokey Trunked Mode OnlyCall Queued Trunked Mode Only Alert TonesLow Battery Warning System Busy Trunked Mode OnlyCall Denied Trunked Mode Only Carrier Control TimerOperation Keypad LOCK/UNLOCK Low Battery Alert Transmit LockoutKey Press Alert Turning on the Radio S = X X X X XY = Z Z Z U T HL S Y S Menu K L = X X N U Y Y Y Y Y YN U K L G H T Page Feature Display Feature Encryption Display Serial Number ROM 12 Hex Digits Number Fields Feature Encryption Data StreamProsound Features EnabledSYSTEM/GROUP/CHANNEL Selection System Selection Primary function for these controlsDisplay registers the new system name on line one Group And Channel Selection Home EMERGENCY/HOME Button DefinitionVoice Modes Aegis and Voice Guard OperationClear Modes Aegis Digital ModeDtmf Aegis Private and Voice Guard Private Modes DSP ERRHardware Transferring Keys Into The Radio Displaying The Currently Used Cryptographic Key Number Key Zero Transmitting An Encrypted Call Private OperationReceiving An Encrypted Call Scanned Group Calls Page Receiving a Call Edacs Trunked Mode OperationSending a Call Conventional Failsoft Emergency Operation Scat OperationDeclaring An Emergency Call Receiving An Emergency CallWide Area System Scan Scanning Trunked SystemsMenu Selection ProSoundPriority System Scan Deleting Groups From a Scan List Pre-Programmed Keypad KeyScanning Trunked Groups Adding Groups To a Scan ListTurning Scan On Nuisance DeleteTurning Scan Off Programmable Entries Is pressed Individual CallsPage Call Storage Lists Sending An Individual Call Trunked Mode Only Telephone Interconnect Calls Receiving a Telephone Interconnect Call Trunked Mode OnlySending a Telephone Interconnect Call Trunked Mode Only Dtmf Overdial/Conventional Mode Telephone Interconnect Page Portable Data Data Displays Data On Operation Data Off OperationExiting Data Calls Scan Lockout ModeMenu Option Data Lockout ModeProFile Select Option Option Availability Status Operation STATUS/MESSAGE OperationMessage Operation Dynamic Regroup Operation Edacs Conventional P1 ScanMacro KEY Operation Emergency OperationSquelch Adjust 256K & UP Version Radios only Conventional Mode OperationMenu Selection Receiving a Call Sending a Call Page Tone Encode Transmission Using 5-Tone Signalling For Emergency DeclarationScanning Conventional Channels Adding Channels to a Scan List Nuisance Delete Deleting Channels from a Scan ListTurning Scan OFF Turning Scan onType 99 Decode Conventional only 100 101 Operating Rules and Regulations102 Operating Tips103 Battery PacksIntrinsically Safe Usage 104 Accessories105 GlossaryMonitor and receive calls from these groups 106Interconnect 107Page 109 110 Warranty111 NICKEL-CADMIUM Battery WarrantyEmergency Numbers

LBI-38732E specifications

The Ericsson LBI-38732E is a prominent piece of communication equipment that showcases advanced features and cutting-edge technologies intended for enhancing network performance and reliability. This model is part of Ericsson's extensive portfolio designed for telecommunications service providers and enterprises looking for robust and scalable solutions.

One of the main features of the LBI-38732E is its high-capacity processing capabilities. It is engineered to handle large volumes of data traffic, ensuring seamless connectivity even during peak usage times. The processing architecture is optimized for low latency, which is critical for applications requiring real-time responsiveness, such as voice over IP and video conferencing.

The LBI-38732E leverages multiple advanced technologies including Software-Defined Networking (SDN) and Network Functions Virtualization (NFV). These technologies allow operators to enhance their network flexibility and agility, facilitating easier management and deployment of new services. By using SDN, the LBI-38732E enables dynamic resource allocation, which can significantly improve operational efficiency.

In addition, the device supports multi-access edge computing (MEC), bringing processing capabilities closer to the end-user. This functionality reduces latency and enhances user experiences, particularly for applications such as augmented reality, IoT, and real-time analytics.

Another key characteristic of the LBI-38732E is its integration with Ericsson's broader ecosystem of network management tools. This integration ensures operators have access to advanced analytics and monitoring capabilities, enabling proactive maintenance and swift issue resolution. The platform also allows for seamless updates and upgrades, ensuring that the technology stays current with evolving market demands.

Furthermore, the LBI-38732E is designed with security as a fundamental aspect. It includes advanced encryption and authentication features to protect sensitive data and ensure the integrity of communications. These security measures are crucial, especially in an era where cyber threats are increasingly sophisticated.

Overall, the Ericsson LBI-38732E stands out as a versatile and powerful solution for modern telecommunications networks. Its innovative features, combined with robust security and management capabilities, make it a valuable asset for operators aiming to deliver high-quality services while adapting to the rapidly changing technological landscape.
Top Page Image Contents