Stanley Black & Decker RW30 user manual YES Valid

Page 18

OPERATION

Set point Position O3. The torch cans only moves on the « Z » axis.

PO4

TORCH:

or

PO4

TORCH:

or

PO4

TORCH:

Set point Position O4. This point should only be set vertically from point Position O1 with automatic tone of this position.

LENGTH: xxmm

WIDTH: xxmm

Display the length and the width of the setting shape (1 mm equals to 0.04 inch).

SURROUND ?

YES - VALID

Display of the step between each bead, (distance in mm, 1 mm equals to 0.04 inch) and estimate welding time in minutes.

BEADS 1 BY 1 ?

YES - VALID

BEADS 1 BY 1 ?

NO - VALID

Welding mode choice: bead by bead, « YES », or continue, « NO ».

If « YES », welding bead by bead (Torch is moving at the be- ginning of the next bead right after previous bead is done).

If « NO », beads are done in “continue”.

WELDING CYCLE

VALID

If VALID key is pressed, Torch will move to starting point of Position O1. Welding will start.

While welding:

RETURN TORCH TO

INITIAL POINT

SURROUND ?

NO - VALID

Surrounding selection: « YES », or « NO », (continuing bead from Position O1 to Position O2 then to Position O3 then to Position O4 and finally to Position O1).

NUMBER BEADS:

xx

Display the number of beads that will be made during the resurfacing (the surrounding is not included in this number). It is possible to modify this number if needed by pressing:

or

SPACING: x.xx mm

WELD.TIME: xxmin

18 - RW30 USER MANUAL

Torch moves to starting point of the welding or at the beginning of the new bead if “bead by bead” mode has been selected.

WELDING CYCLE

SURROUND

Surrounding welding if that option has been selected.

WELDING CYCLE

BEAD xxx/yyy

Shows the bead’s number in welding, « xxx », and the to- tal number of beads of the whole resurfacing of the area, «yyy».

If « bead by bead » option is selected, the following screen appears at the end of the previous bead and after the torch is set.

VALID TO START

FOLLOWING BEAD

Image 18
Contents Robotic Welder General Information Table of Contents Declaration of Conformity Weisbeck, AndySafety Symbols Local Safety RegulationsSafety Precautions Shock HazardWelding Hazards Rays from the ARCGAS Cylinders Exhaust Fumes Make Sure Sparks from the Engine Exhaust do not Start a Fire Operation Claw VersionClamp Version Setting the Stick OUT Automatic Track Mode Automatic POINTS/FROG ModeCharlie Control Unit Controls Stop Printing Data Language SettingSetting the Date and Time Manual Data EntryOperator Dialogue HelloYES Valid Return Torch to Initial Point Error Messages Spacing x.xx mm WELD.TIME xxminUnvalid Point Return to PO1 Troubleshooting « on » TRANSLAMATIC‘s green light does not workFeeding Specifications RW30110 / RW30112RW30 Heater Installed 2009 or Earlier RW30 Cold Weather Update KITAccessories & Parts Spare Parts Master Power Switch 2009 or Earlier Master Power Switch 2010 or LaterTemplate Guage RW30110 / RW30112 Parts List & Illustration RW30120 Parts List & Illustration RW30110 / RW30112 / RW30120 Left Side Illustration Right Side Assembly RW30110 / RW30112 / RW30120 Right Side IllustrationRW30110 / RW30112 / RW30120 Motor Board RW30110 / RW30112 / RW30120 Support Platform RW30110 / RW30112 / RW30120 Support Assembly Clamp Assembly Torch Support Parts List & Illustration Torch Support Pull GUN Illustration Page Stanley Hydraulic Tools