TROUBLESHOOTING | ||
| Observe all Safety Guidelines detailed throughout this manual |
|
|
|
|
PROBLEMS
(SYMPTOMS)
POSSIBLE
CAUSE
RECOMMENDED
COURSE OF ACTION
Basic Machine Problems
Input fuses keep blowing | 1. | Improperly sized input fuses. | 1. | Make sure fuses are properly | ||||
|
|
|
|
|
| sized. See installation section of | ||
|
|
|
|
|
| this manual for recommended | ||
|
|
|
|
|
| sizes. | ||
|
|
|
|
|
|
|
| |
|
| 2. | Improper Weld Procedure requir- | 2. | Reduce output current, duty | |||
|
|
|
| ing output levels in excess of |
| cycle, or both. | ||
|
|
|
| machine rating. |
|
|
| |
|
|
|
|
|
|
|
| |
|
| 3. | Major physical or electrical dam- | 3. | Contact your local authorized | |||
|
|
|
| age is evident when the covers |
| Lincoln Electric Field Service | ||
|
|
|
| are removed. |
| facility for technical assistance. | ||
|
|
|
|
|
|
| ||
Machine will not power up (no lights) | 1. | No Input Power | 1. | Make sure input supply discon- | ||||
|
|
|
|
|
| nect has been turned ON. Check | ||
|
|
|
|
|
| input fuses. Make certain that the | ||
|
|
|
|
|
| Power Switch (SW1) on the | ||
|
|
|
|
|
| power source is in the “ON” posi- | ||
|
|
|
|
|
| tion. | ||
|
|
|
|
|
|
|
| |
|
| 2. | Input voltage is too low or too | 2. | Make certain that input voltage is | |||
|
|
|
| high. |
| correct, according to the Rating | ||
|
|
|
|
|
| Plate located on the rear of the | ||
|
|
|
|
|
| machine. | ||
|
|
|
|
|
|
| ||
Machine wonʼt weld, canʼt get any | 1. | Input voltage is too low or too high. | 1. | Make certain that input voltage is | ||||
output. |
|
|
|
| correct, according to the Rating | |||
|
|
|
|
|
| Plate located on the rear of the | ||
|
|
|
|
|
| machine. | ||
|
|
|
|
|
|
|
| |
|
| 2. | Thermal Error. | 2. | See “Thermal LED is ON” sec- | |||
This problem will normally be |
|
|
|
| tion. | |||
accompanied by an error code. See |
|
|
|
|
|
| ||
3. | Secondary current limit has been | 3. | Possible short in output circuit. If | |||||
“Status Light” section of this docu- | ||||||||
ment for additional information. |
|
| exceeded. (see error 54) |
| condition persists, contact an | |||
|
|
| 3a. Input control board fault (see |
| authorized Lincoln Electric Field | |||
|
|
|
| input control board error status). |
| Service facility. | ||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
POWER WAVE® S350