Lincoln Electric IM610-A manual Input Connections, Gas Solenoid Inlet Fitting Power Input Cable

Page 12

A-5

INSTALLATION

A-5

WARNING

BUILDUP OF SHIELDING GAS may harm health or kill.

• Shut off shielding gas supply when not in use.

•SEE AMERICAN NATIONAL STANDARD Z-49.1, “SAFETY IN WELDING AND CUTTING” PUB- LISHED BY THE AMERICAN WELDING SOCIETY.

1.Chain the cylinder to a wall or other stationary sup- port to prevent the cylinder from falling over. Insulate the cylinder from the work circuit and earth ground.

FIGURE A.5

Flow Regulator

Cylinder Valve

Gas Hose

2.With the cylinder securely installed, remove the cylinder cap. Stand to one side away from the out- let and open the cylinder valve very slightly for an instant. This blows away any dust or dirt which may have accumulated in the valve outlet.

WARNING

BE SURE TO KEEP YOUR FACE AWAY FROM THE VALVE OUTLET WHEN “CRACKING” THE VALVE. Never stand directly in front of or behind the flow regulator when opening the cylinder valve. Always stand to one side.

3.Attach the flow regulator to the cylinder valve and tighten the union nut securely with a wrench. The flow regulator for carbon dioxide must have a plas- tic washer seated in the fitting that attaches to the cylinder to prevent leakage. Refer to K1800-1 in the accessories section.

4.Refer to Figure A.6. Attach one end of inlet gas hose to the outlet fitting of the flow regulator and tighten the union nut securely with a wrench. Connect the other end to the SP-175 Plus Gas Solenoid Inlet Fitting (5/8-18 female threads — for CGA — 032 fitting). Make certain the gas hose is not kinked or twisted.

INPUT CONNECTIONS

Refer to Figure A.6.

The SP-175 Plus has two input connections, the power input cable, and the Gas Solenoid Inlet Fitting. Both connections are located on the rear of the machine.

FIGURE A.6

Gas Solenoid

Inlet Fitting

Power

Input

Cable

SP-175 PLUS

Image 12

Contents SP-175 Plus Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a LʼArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Installation Safety Precautions Read entire installation section before startingInstallation Identify and Locate ComponentsWork Clamp Installation Work Cable InstallationSelect Suitable Location StackingGUN Installation Connecting Gun Cable to the SP-175 PlusGAS Connection Gas Solenoid Inlet Fitting Power Input Cable Input ConnectionsLine Cord Connection Electrical Input Connection for Rated OutputVolt Input Connection Observe all safety information throughout this manual OperationFumes and Gases can be dangerous Welding Sparks can cause fire or explosionControls and Settings Design Features AdvantagesGeneral Description Welding CapabilityWire Loading Welding OperationsSequence of Operation Friction Brake Adjustments Wire ThreadingShielding Gas Making a WeldChanging Machine Over to Feed Other Wire Sizes Cleaning Tip And NozzleProcess Guidelines Wire Feed Overload Protection Overload ProtectionOutput Overload Thermal ProtectionLearning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARCGmaw MIG Welding ARC Process SelectionFor Gmaw MIG Process Common Metals Joint Types and PositionsFor Fcaw Innershield Process Butt WeldsWelding In The Vertical Position PenetrationFillet Welds Machine SET UP for the SELF-SHIELDED Fcaw Process Welding Techniques for the Self Shielded Fcaw ProcessVertical-down Welding Correct Welding PositionCorrect Electrical Stickout ESO Correct Welding SpeedHelpful Hints PracticeMachine SET UP for the Gmaw MIG Process Welding Techniques for the Gmaw MIG ProcessFigure B.24 Troubleshooting Welds To Correct Poor Penetration in order of impor- tanceTo Eliminate a Ropy Convex Bead in order of importance To Eliminate Stubbing* in order of importanceProper Gun Handling Application Chart Accessories Optional AccessoriesK1799-1 Argon-Mixed Gas Adjustable Regulator and Hose Kit K586-1 Deluxe Adjustable Gas Regulator Hose KitReplacement Parts Innershield Fcaw ConversionMaintenance Maintenance Safety PrecautionsItems Requiring no Maintenance Routine and Periodic MAINTE- NanceGUN and Cable Maintenance Configuration of Components in Wire Feeding SystemFor Magnum 100L GUN Contact Tip Cable Liner Drive RollChanging the Contact TIP Changing Drive RollRoll onto the drive shaft SP-175 Plus Changing Liner Liner trim lengthGUN Handle Parts Figure D.3 SP-125 PlusTroubleshooting HOW to USE Troubleshooting GuideProblems Possible Areas Symptoms Misadjustments Recommended Course of ActionGAS Flow Problems Welding Problems Wiring Diagrams SP-175 Plus Wiring Diagram CodePage How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? $700.00Precaucion Warnung