Lincoln Electric IM610-A manual Safety Precautions, Identify and Locate Components, Installation

Page 9

A-2	INSTALLATION	A-2
Read entire installation section before starting		FIGURE A.1
installation.
SAFETY PRECAUTIONS	1	2
SAFETY PRECAUTIONS		2

WARNING

ELECTRIC SHOCK can kill.

•Only qualified personnel should perform this installation.

W
ELDING			AMP
25-1			AMP	RANGE
		25		RANGE
SP-
175	Plus
	Plus

•Only personnel that have read and under- stood the SP-175 Plus Operating Manual should install and operate this equipment.

•Machine must be plugged into a receptacle which is grounded per any national, local or other applicable electrical codes.

• The SP-175 Plus power switch is to be in the OFF (“O”) position when installing work cable and gun and when connecting power cord to input power.

IDENTIFY AND LOCATE

COMPONENTS

4

3

6

5

If you have not already done so, unpack the SP-175 Plus from its carton and remove all packing material around the SP-175 Plus . Remove the following loose

items from the carton (see Figure A.1):	7

1. SP-175 Plus

2.Gun and cable assembly(1)

3.Literature and miscellaneous including:

a)This operating manual

b)A contact tip for .030” (0.8 mm) diameter wire.

c)A contact tip for .035” (0.9 mm) diameter wire.

4.10 ft (3.0 m) work cable.

5.Work clamp.

6.Sample Spool of L-56 .025 MIG Wire.

7.Adjustable mixed-Gas Regulator & Hose.

For available options and accessories refer to the accessories section later in this manual.

1)As shipped from the factory, the SP-175 Plus gun liner is ready to feed .023” (0.6 mm) -.035 (0.9 mm)

wire. The contact tip is sized for .025” (0.6 mm) wire SP-175 PLUS feeding.

Image 9

Contents SP-175 Plus California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a LʼArc Précautions DE SûretéPlease Examine Carton and Equipment For Damage Immediately Thank YouTable of Contents Installation Read entire installation section before starting Safety PrecautionsInstallation Identify and Locate ComponentsWork Cable Installation Work Clamp InstallationSelect Suitable Location StackingGUN Installation Connecting Gun Cable to the SP-175 PlusGAS Connection Input Connections Gas Solenoid Inlet Fitting Power Input CableLine Cord Connection Electrical Input Connection for Rated OutputVolt Input Connection Operation Observe all safety information throughout this manualFumes and Gases can be dangerous Welding Sparks can cause fire or explosionDesign Features Advantages Controls and SettingsGeneral Description Welding CapabilityWire Loading Welding OperationsSequence of Operation Wire Threading Friction Brake AdjustmentsMaking a Weld Shielding GasChanging Machine Over to Feed Other Wire Sizes Cleaning Tip And NozzleProcess Guidelines Overload Protection Wire Feed Overload ProtectionOutput Overload Thermal ProtectionLearning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARCGmaw MIG Welding ARC Process SelectionFor Gmaw MIG Process Joint Types and Positions Common MetalsFor Fcaw Innershield Process Butt WeldsWelding In The Vertical Position PenetrationFillet Welds Welding Techniques for the Self Shielded Fcaw Process Machine SET UP for the SELF-SHIELDED Fcaw ProcessVertical-down Welding Correct Welding PositionCorrect Welding Speed Correct Electrical Stickout ESOPractice Helpful HintsWelding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG ProcessFigure B.24 To Correct Poor Penetration in order of impor- tance Troubleshooting WeldsTo Eliminate a Ropy Convex Bead in order of importance To Eliminate Stubbing* in order of importanceProper Gun Handling Application Chart Optional Accessories AccessoriesK1799-1 Argon-Mixed Gas Adjustable Regulator and Hose Kit K586-1 Deluxe Adjustable Gas Regulator Hose KitInnershield Fcaw Conversion Replacement PartsMaintenance Safety Precautions MaintenanceItems Requiring no Maintenance Routine and Periodic MAINTE- NanceConfiguration of Components in Wire Feeding System GUN and Cable MaintenanceFor Magnum 100L GUN Contact Tip Cable Liner Drive RollChanging the Contact TIP Changing Drive RollRoll onto the drive shaft SP-175 Plus Liner trim length Changing LinerFigure D.3 SP-125 Plus GUN Handle PartsHOW to USE Troubleshooting Guide TroubleshootingRecommended Course of Action Problems Possible Areas Symptoms MisadjustmentsGAS Flow Problems Welding Problems SP-175 Plus Wiring Diagram Code Wiring DiagramsPage New Lessons in Arc Welding How To Read Shop DrawingsNeed Welding Training? $700.00Precaucion Warnung