Lincoln Electric IM610-A manual GUN Handle Parts, Figure D.3 SP-125 Plus

Page 39

D-5		MAINTENANCE	D-5
GUN HANDLE PARTS

The gun handle consists of two halves that are held together with a collar on each end. To open up the handle, turn the collars approximately 60 degrees counter-clockwise until the collar reaches a stop. Then pull the collar off the gun handle. If the collars are diffi- cult to turn, position the gun handle against a corner, place a screwdriver against the tab on the collar and give the screwdriver a sharp blow to turn the collar past an internal locking rib. See Figure D-3.

Counter-clockwise

FIGURE D.3

SP-125 PLUS

Image 39

Contents SP-175 Plus California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a LʼArc Précautions DE SûretéPlease Examine Carton and Equipment For Damage Immediately Thank YouTable of Contents Installation Identify and Locate Components Safety PrecautionsRead entire installation section before starting InstallationStacking Work Clamp InstallationWork Cable Installation Select Suitable LocationGUN Installation Connecting Gun Cable to the SP-175 PlusGAS Connection Input Connections Gas Solenoid Inlet Fitting Power Input CableLine Cord Connection Electrical Input Connection for Rated OutputVolt Input Connection Welding Sparks can cause fire or explosion Observe all safety information throughout this manualOperation Fumes and Gases can be dangerousWelding Capability Controls and SettingsDesign Features Advantages General DescriptionWire Loading Welding OperationsSequence of Operation Wire Threading Friction Brake AdjustmentsMaking a Weld Shielding GasChanging Machine Over to Feed Other Wire Sizes Cleaning Tip And NozzleProcess Guidelines Thermal Protection Wire Feed Overload ProtectionOverload Protection Output OverloadSELF-SHIELDED Fcaw Welding ARC Learning to WeldLearning to Weld ARC-WELDING CircuitGmaw MIG Welding ARC Process SelectionFor Gmaw MIG Process Butt Welds Common MetalsJoint Types and Positions For Fcaw Innershield ProcessWelding In The Vertical Position PenetrationFillet Welds Correct Welding Position Machine SET UP for the SELF-SHIELDED Fcaw ProcessWelding Techniques for the Self Shielded Fcaw Process Vertical-down WeldingCorrect Welding Speed Correct Electrical Stickout ESOPractice Helpful HintsWelding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG ProcessFigure B.24 To Eliminate Stubbing* in order of importance Troubleshooting WeldsTo Correct Poor Penetration in order of impor- tance To Eliminate a Ropy Convex Bead in order of importanceProper Gun Handling Application Chart K586-1 Deluxe Adjustable Gas Regulator Hose Kit AccessoriesOptional Accessories K1799-1 Argon-Mixed Gas Adjustable Regulator and Hose KitInnershield Fcaw Conversion Replacement PartsRoutine and Periodic MAINTE- Nance MaintenanceMaintenance Safety Precautions Items Requiring no MaintenanceContact Tip Cable Liner Drive Roll GUN and Cable MaintenanceConfiguration of Components in Wire Feeding System For Magnum 100L GUNChanging the Contact TIP Changing Drive RollRoll onto the drive shaft SP-175 Plus Liner trim length Changing LinerFigure D.3 SP-125 Plus GUN Handle PartsHOW to USE Troubleshooting Guide TroubleshootingRecommended Course of Action Problems Possible Areas Symptoms MisadjustmentsGAS Flow Problems Welding Problems SP-175 Plus Wiring Diagram Code Wiring DiagramsPage $700.00 How To Read Shop DrawingsNew Lessons in Arc Welding Need Welding Training?Precaucion Warnung

MAINTENANCE

GUN HANDLE PARTS

FIGURE D.3

SP-125 PLUS