Lincoln Electric IM610-A manual Optional Accessories

Page 33

C-1

ACCESSORIES

C-1

OPTIONAL ACCESSORIES

1.K520 Utility Cart — Designed to transport the Lincoln family of small welders. Has provisions for mounting a single gas cylinder. Has front casters and large rear wheels. Handle height is easily adjustable. Bottom tray provided for tools and accessories. Easy assembly required; takes less than 15 minutes.

2.K1800-1 CO2 Adjustable Regulator and Hose Kit — Includes an adjustable pressure flow regulator for

use on CO2 cylinders.

Weld shielding gas may be obtained from a weld- ing supply distributor.

Also included is a gas hose which connects to the rear of the welder.

See “Gas Connection” in Installation section for installation instructions.

3.K1799-1 Argon-Mixed Gas Adjustable Regulator and Hose Kit (1)

Includes an adjustable pressure and flow regulator for use on argon-mixed gas cylinders. Also includ- ed is a gas hose which connects to the rear of the welder.

4. K586-1 Deluxe Adjustable Gas Regulator &

Hose Kit

Accommodates CO2 or mixed Gas Cylinders.

5.K663-2 Aluminum Welding Kit — This kit required for welding with .035” aluminum wire. Included with this kit are a drive roll and idle roll assembly, liner and guide tubes and a contact tip.

It is important when changing between welding with steel wire and aluminum to exchange these components due to the lubricant applied to steel wire. Failure to do so may result in con- taminated welds when welding aluminum.

See Maintenance section for instructions on installing drive roll, cable liner, contact tip and their proper con- figuration.

6.K695-2 Spot / Stitch Timer Kit — Includes spot timer to control the spot welding arc time, and a stitch timer to control the on/off cycle time of the arc to prevent burnthrough on thin gauge metals. Also includes spot welding nozzle.

The Spot/Stitch Timer Kit installs inside the wire feed compartment, replacing the blank panel locat- ed below the gun trigger lead connectors, per the installation instructions included with the kit.

7.K549-1 .035 (0.9 mm) Innershield Welding Kit Includes a contact tip, a gasless nozzle and a cable liner to permit the Magnum™ 100L gun and cable to use .035” (0.9 mm) diameter flux-cored electrode. Also included is a spool of .035 (0.9 mm) Innershield NR-211-MP.

SP-175 PLUS

Image 33

Contents SP-175 Plus California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a LʼArc Précautions DE SûretéPlease Examine Carton and Equipment For Damage Immediately Thank YouTable of Contents Installation Read entire installation section before starting Safety PrecautionsInstallation Identify and Locate ComponentsWork Cable Installation Work Clamp InstallationSelect Suitable Location StackingGUN Installation Connecting Gun Cable to the SP-175 PlusGAS Connection Input Connections Gas Solenoid Inlet Fitting Power Input CableLine Cord Connection Electrical Input Connection for Rated OutputVolt Input Connection Operation Observe all safety information throughout this manualFumes and Gases can be dangerous Welding Sparks can cause fire or explosionDesign Features Advantages Controls and SettingsGeneral Description Welding CapabilityWire Loading Welding OperationsSequence of Operation Wire Threading Friction Brake AdjustmentsMaking a Weld Shielding GasChanging Machine Over to Feed Other Wire Sizes Cleaning Tip And NozzleProcess Guidelines Overload Protection Wire Feed Overload ProtectionOutput Overload Thermal ProtectionLearning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARCGmaw MIG Welding ARC Process SelectionFor Gmaw MIG Process Joint Types and Positions Common MetalsFor Fcaw Innershield Process Butt WeldsWelding In The Vertical Position PenetrationFillet Welds Welding Techniques for the Self Shielded Fcaw Process Machine SET UP for the SELF-SHIELDED Fcaw ProcessVertical-down Welding Correct Welding PositionCorrect Welding Speed Correct Electrical Stickout ESOPractice Helpful HintsWelding Techniques for the Gmaw MIG Process Machine SET UP for the Gmaw MIG ProcessFigure B.24 To Correct Poor Penetration in order of impor- tance Troubleshooting WeldsTo Eliminate a Ropy Convex Bead in order of importance To Eliminate Stubbing* in order of importanceProper Gun Handling Application Chart Optional Accessories AccessoriesK1799-1 Argon-Mixed Gas Adjustable Regulator and Hose Kit K586-1 Deluxe Adjustable Gas Regulator Hose KitInnershield Fcaw Conversion Replacement PartsMaintenance Safety Precautions MaintenanceItems Requiring no Maintenance Routine and Periodic MAINTE- NanceConfiguration of Components in Wire Feeding System GUN and Cable MaintenanceFor Magnum 100L GUN Contact Tip Cable Liner Drive RollChanging the Contact TIP Changing Drive RollRoll onto the drive shaft SP-175 Plus Liner trim length Changing LinerFigure D.3 SP-125 Plus GUN Handle PartsHOW to USE Troubleshooting Guide TroubleshootingRecommended Course of Action Problems Possible Areas Symptoms MisadjustmentsGAS Flow Problems Welding Problems SP-175 Plus Wiring Diagram Code Wiring DiagramsPage New Lessons in Arc Welding How To Read Shop DrawingsNeed Welding Training? $700.00Precaucion Warnung