Lincoln Electric IM806 manual Duplex Receptacles, Motor Starting

Page 14

A-7

INSTALLATION

A-7

 

 

 

GND

115 V

230 V

115 V*

*Current Sensing for Automatic Idle. (Receptacle viewed from front of Machine)

115 V DUPLEX RECEPTACLES

The 115V auxiliary power receptacles should only be used with three wire grounded type plugs or approved double insulated tools with two wire plugs.

The current rating of any plug used with the system must be at least equal to the current load through the associated receptacle (Refer to Table I ). Do not attempt to connect power receptacles in parallel.

TABLE I Maximum Current Draw from 115V Duplex Receptacles and from 120V GFCI duplex Receptacles - No Welding

MOTOR STARTING

Most 1.5 hp AC single phase motors can be started if there is no load on the motor or other load connected to the machine, since the full load current rating of a

1.5hp motor is approximately 20 amperes (10 amperes for 230 volt motors). The motor may be run at full load when plugged into only one side of the duplex receptacle. Larger motors through 2 hp can be run provided the receptacle rating as previously stated is not exceeded. This may necessitate 230V operation only.

Load From

Each Half of

Total From

 

 

115V/230V

Each 115V

Both 115V

 

 

Dual Voltage

Duplex

Duplex

 

 

Receptacle

 

 

 

 

 

 

 

 

 

0

20

40*

 

 

 

1.1 KW

20

40*

 

 

 

3.4 KW

20

40*

 

 

 

5.7 KW

20

20*

 

 

 

8.0 KW

0

0

 

 

 

 

 

 

 

 

*Maximum current draw from each 115V GFCI Duplex is 20 amps

*NEMA 5-20P Plug required for 20Amp Draw

WELDMARK 225

Image 14
Contents Weldmark Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Weldmark InstallationHeight Width Depth Weight Specifications Spark Arrester Installation InstructionsMachine Grounding LiftingTotal Combined Length PRE-OPERATION ServiceWelding Output Cables Electrode and Work Cables GasolineHigh Altitude Operation Connection of Wire FeedersAngle of Operation Location / VentilationInstructions Additional Safety PrecautionsAuxiliary Power Connection of K930- TIG Module to the WeldmarkDuplex Receptacles Motor StartingThese Devices Without Standby Power Connections Auxiliary Power While WeldingSimultaneous Welding and Power Connection of Weldmark 225 to Premises Wiring Engine Features Design FeaturesOther Features OperationRange Switch 20 H.P. CommandPolarity Switch Control SwitchBREAK-IN Period Stopping the EngineDuty Cycle Wire Feed Welding Processes Constant VoltageWelding Process Stick Constant Current WeldingHigh Accessories K1745-1 Single GAS Cylinder HolderStick Wire FeedRecommended Equipment TIGRoutine Maintenance MaintenanceSafety Precautions Engine OIL ChangeOIL Filter Change RangerEngine Adjustments Gfci Receptacle Testing and Reset Ting Procedure Troubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Weldmark 225 Wiring Diagram Code DiagramsWeldmark 225 / LN-25 Across the ARC Connection Diagram Connection of Weldmark 225 to LN-7 & K240 Contactor KITM17215-2 30-98E Precaucion Warnung Manufactured by Lincoln Electric Company