Lincoln Electric LF-72/74 service manual Figure D.1

Page 41

Return to Section TOC

Return to Master TOC

D-3	MAINTENANCE	D-3

	FIGURE D.1

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

4.Open the idle arm.

5.Turn power on to the LF-72.

6.Adjust the WFS knob to 300 ipm. Center the knob pointer with the name plate graphics.Activate the gun trigger.

7.Insert the shorting plug into connector J2 on the p.c. board. The shorting plug shorts pins 1 & 5.

(See Figure D.2)

8.Remove the shorting plug. Set aside.

(For Codes below 11289 use 9 thru 17)

9.Adjust the WFS knob to minimum.

10.Insert the shorting plug into connector J2.

11.Adjust the WFS knob until the motor measures 51

±5.5 ipm. (9.5 ± 1.0 rpm).

12.Remove the shorting plug.

13.Adjust the WFS knob to maximum.

14.Insert the shorting plug into connector J2.

15.Adjust the WFS until the motor measures 793 ± 5.5 ipm (146.7 ± 1.0 rpm.)

16.Remove the shorting plug.

17.Release the gun trigger.

(For Codes above 11290 use 18)

18.Replace P2 from the harness into connector J2.

19.Turn off power.

20.Secure the wraparound to the LF-72 with 5 screws.

FIGURE D.2

J2 CONNECTOR

LF-72/74 SINGLE/DUAL

Image 41

Contents LF-72/74 Safety Electric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéMaster Table of Contents for ALL Sections Section A-1 Table of ContentsInstallation Section Amp Rating Duty Cycle InstallationMounting Safety PrecautionLocation Swivel Mount Bench MountBoom Mount SuspendedWeld Cable Sizes Weld Cable Connection Coaxial Weld CablesControl Cable Connections INSTALLATIONA-7Analog Control Cable Pin Function Miller Power Source Lincoln Wire FeederAnalog Miller Control Cable Adapter K2335-1 Welding GUN/WIRE Feeder Trigger Connector Wire Drive SystemsRemote Sense Lead Specifications High Frequency ProtectionMagnum GUN and Cable Assemblies Welding GUNS, Torches and ACCES- SoriesRolls.FIGURE A.4 Procedure for Changing Drive and Idle Roll SetsWire Drive Configuration Set the pressure arm as follows See Figure A.6 Pressure ARM AdjustmentGun Receiver For use With Bushing Wire Reel Loading Figure A.9 Weld Wire RoutingShielding GAS Connection To install Lincoln conduit See Figure A.10b Installing ElectrodeConduit Kits For Codes 11209, 11210, 11211 and aboveFigure A.12b Aluminum Wire PreparationsBase Model Bench Model Standard Duty Bench Model Heavy Duty INSTALLATIONA-18Cable Typical System ConfigurationsLF-72/74 Section B-1 Operation SectionGAS Input Work Connection OperationRecommended Processes Common Welding AbbreviationsProduct Description Figure B.1 Case Front Controls Description Front Panel Controls and ConnectionsCold FEED/GAS Purge Switch Burnback and Postflow Timer KITStep Trigger Interlock Switch Remote Voltage Control KITTrigger Connector 5-PIN Amphenol Wire Feed Speed KnobGUN Receiver Bushing K1500-2 Trigger InterlockSection C-1 Accessories SectionOptional Kits AccessoriesLF-72s Accessories Key LF-72/74 Section D-1 Maintenance SectionMaintenance MaintenanceCalibration Specification Routine MaintenanceFigure D.1 Figure D.3 Major Component Location Section AA Section AA-1Model WFS Range Wire SizesAA-2 Figure AA.1 AA-3AA-4 AA-5 Coaxial Weld Cable AA-6K1797-xx INSTALLATIONAA-7AA-7 AA-8 AA-9 Drive Roll Kits Steel or Cored WiresFigure AA.3 AA-10Changing the Gun Receiver Bushing AA-11Lation or changing drive rolls and/or GuidesAA-12 Assembly of Drive Rolls and Wire GuidesSet the pressure arm as follows See Figure AA.8 AA-13AA-14 Loading 16 to 44 lb .3 20kg Spools See figure AA.8 AA-15Figure AA.11 AA-16Figure AA.12a AA-17Figure AA.12b AA-18AA-19 Common Equipment SET-UPS AA-20INSTALLATIONAA-20AA-21 Figure AA.15 High Volume ProductionAA-22 Figure AA.16 Portable WeldingSection BB Section BB-1Fcaw Innershield or Outershield BB-2BB-3 Required EquipmentFigure BB.1 Case Front Controls Description BB-4K2426-3 model BB-5K2426-1 and K2426-2 models BB-6 SwitchSection CC-1 CC-2 CC-3 CC-4 CC-5 CC-6 Section DD Section DD-1Nal wiring To verify the wire feed speedWhen inching with gun trigger, electrode WFS knob setting Could remain energized Several secondsDD-3 MAINTENANCEDD-3DD-4 Figure DD.3 Major Component LocationSection E-1 Theory of Operation SectionReturn to Section Theory of OperationControl Board LF-72/74 Section F-1 Troubleshooting & Repair SectionHOW to USE Troubleshooting Guide Troubleshooting & RepairPC Board Troubleshooting Procedures Function Problems Function Problems Troubleshooting & Repair Test Description Drive Motor and Tach Feedback TestTest Procedure GAS Solenoid Test Troubleshooting and RepairFigure F.3 Leads 552, 552B Test ProcedureDiode Bridge Test 552B + 552A Wire Speed Potentiometer Test 14F-14 Wire Speed Potentiometer TestPC Board Removal and Replacement Removal Procedure Replacement Procedure Control PC Board Removal and Replacement ProcedureTroubleshooting and Repair Procedure Wire Drive Motor and Gear BOX Removal and ReplacementProcedure Replacement Procedures Operation Verification SET UPLF-72/74 Section G-1 Electrical Diagrams SectionLF-72/74 Electrical DiagramsTimer KIT Board Normal Speed Micro Internal panel Motor Connecter Summary High Torque Setting engages Schematic Common Analog Control PC Board G4559 Sheet Electrical Diagrams Electrical Diagrams PC Board Assembly Common Analog Control G4560-2E0