Lincoln Electric LF-72/74 service manual Assembly of Drive Rolls and Wire Guides, AA-12

Page 54

AA-12

INSTALLATION

AA-12

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

ASSEMBLY OF DRIVE ROLLS AND WIRE GUIDES

WARNING

ELECTRIC SHOCK can kill.

Turn the input power OFF at the welding power source before instal- lation or changing drive rolls and/or guides.

Do not touch electrically live parts.

When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several seconds after the gun trigger is released.

Only qualified personnel should perform mainte- nance work.

------------------------------------------------------------------------

To remove drive rolls and wire guides: (See Figure AA.6)

1.Turn power off at the welding power source.

2.Remove the outer wire guide.

3.Rotate 4 triangular rings to the unlocked position.

4.Open the pressure arms.

5.Remove the drive rolls and inner wire guide.

FIGURE AA.6

2 PRESSURE ARMS ROTATE DOWN

4 TRIANGULAR RINGS IN UNLOCKED POSITION

OUTER WIRE GUIDE

To install drive rolls and wire guides: (See Figure AA.7 and AA.7a)

1.Turn off power at the welding power source.

2.Open pressure arms.

3.Assemble the inner wire guide.

4.Slide the drive rolls onto the drive hubs. (See figure AA.7)

5.Close the pressure arms.

6.Rotate 4 triangular rings to the locked position. (See figure AA.7a)

7.Assemble the outer wire guide.

8.Adjust the pressure arms to the recommended set- ting.

FIGURE AA.7

DRIVE HUBS

PRESSURE ARMS

IN OPEN POSITION

INNER WIRE GUIDE

DRIVE ROLLS

FIGURE AA.7a

SLIDE DRIVE ROLL

ON DRIVE HUB

TRIANGULAR RING IN

UNLOCKED POSITION

TRIANGULAR RING IN

LOCKED POSITION

Return to Section TOC

Return to Master TOC

LF-72/74

Image 54
Contents LF-72/74 Safety Electric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation SectionSection A-1 Installation Amp Rating Duty CycleSafety Precaution LocationMounting Boom Mount Bench MountSwivel Mount SuspendedWeld Cable Sizes Coaxial Weld Cables Weld Cable ConnectionINSTALLATIONA-7 Analog Control CableControl Cable Connections Miller Power Source Lincoln Wire Feeder Analog Miller Control Cable Adapter K2335-1Pin Function Remote Sense Lead Specifications Wire Drive SystemsWelding GUN/WIRE Feeder Trigger Connector High Frequency ProtectionWelding GUNS, Torches and ACCES- Sories Magnum GUN and Cable AssembliesProcedure for Changing Drive and Idle Roll Sets Wire Drive ConfigurationRolls.FIGURE A.4 Pressure ARM Adjustment Gun Receiver For use With BushingSet the pressure arm as follows See Figure A.6 Wire Reel Loading Weld Wire Routing Figure A.9Shielding GAS Connection Conduit Kits Installing ElectrodeTo install Lincoln conduit See Figure A.10b For Codes 11209, 11210, 11211 and aboveAluminum Wire Preparations Figure A.12bINSTALLATIONA-18 Base Model Bench Model Standard Duty Bench Model Heavy DutyTypical System Configurations CableLF-72/74 Operation Section Section B-1Operation GAS Input Work ConnectionCommon Welding Abbreviations Product DescriptionRecommended Processes Front Panel Controls and Connections Figure B.1 Case Front Controls DescriptionStep Trigger Interlock Switch Burnback and Postflow Timer KITCold FEED/GAS Purge Switch Remote Voltage Control KITGUN Receiver Bushing K1500-2 Wire Feed Speed KnobTrigger Connector 5-PIN Amphenol Trigger InterlockAccessories Section Section C-1Accessories Optional KitsLF-72s Accessories Key LF-72/74 Maintenance Section Section D-1Calibration Specification MaintenanceMaintenance Routine MaintenanceFigure D.1 Figure D.3 Major Component Location Section AA-1 Section AAWFS Range Wire Sizes AA-2Model AA-3 Figure AA.1AA-4 AA-5 AA-6 Coaxial Weld CableINSTALLATIONAA-7 AA-7K1797-xx AA-8 Drive Roll Kits Steel or Cored Wires AA-9AA-10 Figure AA.3Lation or changing drive rolls and/or AA-11Changing the Gun Receiver Bushing GuidesAssembly of Drive Rolls and Wire Guides AA-12AA-13 Set the pressure arm as follows See Figure AA.8AA-14 AA-15 Loading 16 to 44 lb .3 20kg Spools See figure AA.8AA-16 Figure AA.11AA-17 Figure AA.12aAA-18 Figure AA.12bAA-19 AA-20INSTALLATIONAA-20 Common Equipment SET-UPSFigure AA.15 High Volume Production AA-21Figure AA.16 Portable Welding AA-22Section BB-1 Section BBBB-2 Fcaw Innershield or OutershieldRequired Equipment BB-3BB-4 Figure BB.1 Case Front Controls DescriptionBB-5 K2426-1 and K2426-2 modelsK2426-3 model Switch BB-6Section CC-1 CC-2 CC-3 CC-4 CC-5 CC-6 Section DD-1 Section DDWhen inching with gun trigger, electrode To verify the wire feed speedNal wiring WFS knob setting Could remain energized Several secondsMAINTENANCEDD-3 DD-3Figure DD.3 Major Component Location DD-4Theory of Operation Section Section E-1Theory of Operation Return to SectionControl Board LF-72/74 Troubleshooting & Repair Section Section F-1Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Function Problems Function Problems Troubleshooting & Repair Drive Motor and Tach Feedback Test Test DescriptionTest Procedure Troubleshooting and Repair GAS Solenoid TestTest Procedure Figure F.3 Leads 552, 552BDiode Bridge Test 552B + 552A Wire Speed Potentiometer Test Wire Speed Potentiometer Test 14F-14PC Board Removal and Replacement Control PC Board Removal and Replacement Procedure Removal Procedure Replacement ProcedureTroubleshooting and Repair Wire Drive Motor and Gear BOX Removal and Replacement ProcedureProcedure Replacement Procedures SET UP Operation VerificationLF-72/74 Electrical Diagrams Section Section G-1Electrical Diagrams LF-72/74Timer KIT Board Normal Speed Micro Internal panel Motor Connecter Summary High Torque Setting engages Schematic Common Analog Control PC Board G4559 Sheet Electrical Diagrams Electrical Diagrams PC Board Assembly Common Analog Control G4560-2E0