Iii

SAFETY

iii

WELDING and CUTTING

SPARKS can

cause fire or explosion.

6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire.

Remember that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been “cleaned”. For information, purchase “Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate cir- cuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention During Welding, Cutting and Other Hot Work”, available from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER may explode if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

•Away from areas where they may be struck or subjected to physical damage.

•A safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturer’s recommendations.

Refer to http://www.lincolnelectric.com/safety for additional safety information.

Jan ‘09

IM917-A specifications

The Lincoln Electric IM917-A is a highly advanced welding machine that caters to the needs of industrial and commercial applications. Designed for both expert welders and those new to the craft, this machine offers a rich combination of features and technologies that enhance performance and usability.

One of the standout features of the IM917-A is its robust inverter technology. This innovation allows the machine to provide consistent arc stability and improved control, even at low amperages. This means welders can achieve precision results in various materials, including carbon steel, stainless steel, and aluminum, without the risk of burn-through or warping. Additionally, the inverter design contributes to the IM917-A’s lightweight profile, making it portable and easy to transport to job sites.

The IM917-A employs advanced digital control systems that allow for precise adjustments and monitoring. Welders can access various pre-set programs tailored for different welding processes, significantly speeding up setup times. The intuitive user interface ensures that operators can quickly navigate through settings, achieving optimal parameters for each specific task. This ease of use makes the IM917-A accessible to less experienced welders while meeting the demands of seasoned professionals.

Another noteworthy characteristic of the IM917-A is its versatility. It supports multiple welding processes, including MIG, TIG, Stick, and flux-cored welding. This multi-process capability makes it an ideal machine for workshops looking to maximize their productivity without investing in multiple units. The ability to switch between these processes seamlessly allows users to adapt to various project requirements swiftly.

Safety is prioritized in the design of the IM917-A. It is equipped with features such as over-temperature protection and automatic shutoff, ensuring safe operation during prolonged use. Additionally, its durable construction and high-quality components enhance its reliability and longevity, making it a wise investment for businesses.

In conclusion, the Lincoln Electric IM917-A is a formidable choice for welders of all skill levels. Its combination of advanced inverter technology, user-friendly digital controls, versatile welding processes, and essential safety features sets it apart in the competitive welding equipment market. Whether for commercial, industrial, or even artistic applications, the IM917-A promises to deliver excellent performance and reliable results.