Lincoln Electric IM883-A manual Connection of Prince XL Spool GUN to the Vantage

Page 17

A-9

INSTALLATION

A-9

 

 

 

WARNING

Connection of the LN-25 to the VANTAGE 400 Shut off welder before making any electrical con- nections.

------------------------------------------------------------------------

The LN-25 with or without an internal contactor may be used with the VANTAGE 400. See the appropriate connection diagram in Section F.

1.Shut the welder off.

2.For electrode Positive, connect the electrode cable from the LN-25 to the "+" terminal of the welder and work cable to the "-" terminal of the welder. For electrode Negative, connect the elec- trode cable from the LN-25 to the "-" terminal of the welder and work cable to the "+" terminal of the welder.

3.Attach the single lead from the front of the LN-25 to work using the spring clip at the end of the lead. This is a control lead to supply current to the wire feeder motor; it does not carry welding current.

4.Set the MODE switch to the "CV-WIRE " position.

5.Set the "WELD TERMINALS" switch to "WELD

TERMINALS ON"

6.Set the "ARC CONTROL" knob to "0" initially and adjust to suit.

7.Set the "IDLE" switch to the "AUTO" position. When not welding, the VANTAGE 400 engine will be at the low idle speed. If you are using an LN-25 with an internal contactor, the electrode is not energized until the gun trigger is closed.

8.When the gun trigger is closed, the current sens- ing circuit will cause the VANTAGE 400 engine to go to the high idle speed, the wire will begin to feed and the welding process started. When weld- ing is stopped, the engine will revert to low idle speed after approximately 12 seconds unless welding is resumed.

CAUTION

If you are using an LN-25 without an internal con- tactor, the electrode will be energized when the VANTAGE 400 is started.

------------------------------------------------------------------------

Spool Gun (K487-25) and Cobramatic to VANTAGE 400

•Shut the welder off.

•Connect per instructions on the appropriate connec- tion diagram in Section F.

Connection of PRINCE XL SPOOL GUN to the VANTAGE 400

Connection of the Prince XL Spool Gun requires the use of the K1849-1 Adapter Module.

•Shut the Welder off.

•For electrode Positive, connect the electrode cable to the "+" terminal of the welder and work cable to the "-" terminal of the welder. For electrode Negative, connect the electrode cable "-" terminal of the welder and work cable to the "+" terminal of the welder.

•Connect the Control Cable of the Spool Gun to the Adapter Module and connect the Control Cable of the Adapter Module to the Welder.

•Connect the Gas Hose.

•Set the MODE switch to the "CV-WIRE " position.

•Set the "WELD TERMINALS" switch to "WELD

TERMINALS ON".

•Set the "ARC CONTROL" knob to "0" initially and adjust to suit.

•Set the “IDLE” switch to the “HIGH” position.

VANTAGE® 400

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Vantage California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a LʼArc Précautions DE SûretéThank You Table of Contents Section E Section DSection F 528Technical Specifications Vantage 400 K2410-1 K2410-2 InstallationLocation and Ventilation Safety PrecautionsVRD Voltage Reduction Device High Temperature Operation PRE-OPERATION Engine ServiceTowing Vehicle MountingRemote Control Battery ConnectionOIL FuelMachine Grounding Electrical ConnectionsWelding Output Cables Total Combined Length of Electrode and Work CablesGfci Duplex Receptacles Auxiliary Power ReceptaclesStandby Power Connections Connection of Vantage 400 to Premises Wiring Connection of LN-15 to the Vantage Shut the welder off Connection of Lincoln Electric Wire FeedersAcross The-Arc Model Control Cable ModelConnection of Prince XL Spool GUN to the Vantage General Description OperationFigure B.1 Weld Mode Selector SwitchTable B.1 Wire Feeder Voltmeter SwitchGlow Plug Push Button Engine ControlsStarting the Engine Table B.2Welder Operation Stopping the EngineDuty Cycle Electrode InformationTable B.3 TIG WeldingTypical Current Ranges 1 for Tungsten ELECTRODES2 ARC Gouging Wire WELDING-CVAuxiliary Power Field Installed Options / ACCES- Sories AccessoriesWire Feeder Options TIG OptionsRoutine Maintenance MaintenanceOIL Filter Change AIR CleanerEngine OIL Change Maintenance Bleeding the Fuel System Cooling SystemTightening the FAN Belt Battery Maintenance Engine AdjustmentServicing Optional Spark ArrestorGfci Receptacle Testing and RESET- Ting Procedure Welder / Generator MaintenanceHOW to USE Troubleshooting Guide TroubleshootingContact your local Lincoln Authorized Field Service FacilityLincoln Welding without a control cable Troubleshooting Faulty control cable. Repair or Your local Lincoln Authorized Field Service FacilityDiagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams 400 WiringDiagram Print DimensionPrecaucion Warnung
Top Page Image Contents