Lincoln Electric IM10028-B manual Troubleshooting

Page 29

E-3

TROUBLESHOOTING

E-3

 

 

 

 

Observe all Safety Guidelines detailed throughout this manual

 

 

 

 

PROBLEMS

(SYMPTOMS)

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

 

Engine will not go to high idle when

1.

No voltage signal from the

 

using auxiliary power.

 

current sensor.

 

 

2.

Auxiliary power load less than

 

 

 

100 to 150 watts.

 

 

3.

Faulty P.C. Board.

 

 

 

 

 

Engine will not crank or is hard to

1.

Battery will not hold a charge.

 

crank.

 

Faulty Battery.

 

 

2.

No or insufficient charging

 

 

 

current.

 

 

3.

Loose battery cable

 

 

 

connection(s).

 

 

 

 

 

Engine shuts down.

1.

Out of fuel.

 

 

2.

Low oil level.

 

 

 

 

Engine does not develop full power.

1. Fuel filter clogged.

 

 

2.

Air filter clogged.

 

 

 

 

 

Engine is hard to start.

1.

Spark plugs do not have

 

 

 

specified gap.

 

 

2.

Spark plugs are fouled.

 

 

3.

Out of fuel.

 

 

4.

Fuel filter clogged.

 

 

5.

Electric fuel pump not working.

 

 

 

(Electric pump equipped models

 

 

 

only.)

 

 

6.

Mechanical fuel pump not work-

 

 

 

ing.

 

 

 

 

 

 

 

 

If all recommended possible areas of misadjustment have been checked and the problem persists, Contact your local Lincoln Authorized Field Service Facility.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

EAGLE™ 10,000 PLUS

Image 29
Contents Eagle 10,000 Plus Safety Depends on YouCalifornia Proposition 65 Warnings SafetySafety Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté IvSAFETYThank You Table of Contents Installation Machine Grounding Safety PrecautionsSpark Arrester TowingBattery Connections PRE-OPERATION ServiceGasoline Fuel only GasolineWelding Output Cables Additional Safety PrecautionTotal Combined Length of Electrode and Work Cables Angle of OperationInstructions Additional Safety PrecautionsLocation / Ventilation StackingWelder Operation Auxiliary PowerDevices Without Addi Tional Resistive Type Loads Standby Power Connections Auxiliary Power While WeldingSimultaneous Welding and Power Connection of Eagle 10,000 Plus to Premises Wiring Operation Engine SwitchGENERAL DESCRIPTION Welder Controls Function and Operation23 H.P. Command CH23S Range SwitchEagle 10,000 Plus Approximate Fuel Consumption Control DialBREAK-IN Period STARTING/SHUTDOWN InstructionsStarting the Engine Stopping the EngineTypical Current Ranges 1 for Tungsten ELECTRODES2 Welding ProcessStick Constant Current Welding Scratch Start TIG Constant Current WeldingARC Gouging 5OPERATIONB-5K1745-1 Welding GAS Cylinder LOX Tank Holder AccessoriesStick RECOMMENDED EQUIPMENTTIG K1783-4 TIG TorchSafety Precautions MaintenanceRoutine Maintenance Engine OIL ChangeOIL Filter Change AIR Cleaner and Other MaintenanceEngine Adjustments HOW to USE Troubleshooting Guide TroubleshootingTroubleshooting Troubleshooting Diagrams M22195 Dimension PrintEagle 10,000 Plus Eagle 10,000 Plus Precaucion Warnung