Lincoln Electric 225 manual Angle of Operation, High Altitude Operation, Location / Ventilation

Page 12

A-5

INSTALLATION

A-5

 

 

 

Angle of Operation

Internal combustion engines are designed to run in a level condition which is where the optimum perfor- mance is achieved. The maximum angle of operation for the engine is 15 degrees from horizontal in any direction. If the engine is to be operated at an angle, provisions must be made for checking and maintain- ing the oil at the normal (FULL) oil capacity in the crankcase in a level condition.

When operating at an angle, the effective fuel capaci- ty will be slightly less than the specified 10 gallons.

High Altitude Operation

If the Weldmark 225 will be consistently operated at altitudes above 5000 ft, a carburetor jet designed for high altitudes should be installed. This will result in better fuel economy, cleaner exhaust, and longer spark plug life. It will not give increased power which is decreased at higher altitudes. Engine horsepower is reduced by 3.5% per 1000 feet for altitudes above 377 feet.

CAUTION

Do not operate a Weldmark 225 with a high alti- tude jet installed at altitudes below 5000 ft. This will result in the engine running too lean and result in higher engine operating temperatures which can shorten engine life.

High altitude jet kits are available from the engine manufacturer. For the Kohler model order kit part no. 2475501.

WARNING

Muffler Relocation Shut off welder and allow muffler to cool before touching muffler.

The Weldmark 225 is shipped with the exhaust com- ing out on the left side. The exhaust can be changed to the opposite side by removing the two screws that hold the exhaust port cover in place and installing the cover on the opposite side. (Operating the Weldmark 225 without the cover in place will result in a higher noise level and no increase in machine output.)

Location / Ventilation

The welder should be located to provide an unrestrict- ed flow of clean, cool air to the cooling air inlets and to avoid heated air coming out of the welder recirculating back to the cooling air inlet. Also, locate the welder so that engine exhaust fumes are properly vented to an outside area.

WARNING

• Damage to the fuel tank may cause fire or explosion. Do not drill holes in the WELDMARK 225 base or weld to the WELDMARK 225 base.

Connection of Wire Feeders

WARNING

Shut off welder before making any electrical connections.

Wire Feed (Constant voltage)

Connection of the LN-25 to the Weldmark 225

Shut the welder off.

Connect the electrode cable from the LN-25 to the “ELECTRODE” terminal of the welder. Connect the work cable to the “TO WORK” terminal of the welder.

Position the welder “Polarity” switch to the desired polarity, either DC (-) or DC (+).

Position the “RANGE” switch to the “WIRE FEED” position.

Attach the single lead from the LN-25 control box to the work using the spring clip on the end of the lead - it carries no welding current.

Place the idler switch in the “AUTO” position.

Adjust wire feed speed at the LN-25 and adjust the welding voltage with the output “CONTROL” at the welder.

NOTE: The welding electrode is energized at all times, unless an LN-25 with built-in contactor is used. If the output “CONTROL” is set below “3”, the LN-25 contactor may not pull in.

WELDMARK 225

Image 12
Contents Weldmark Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Installation Technical Specifications Weldmark 225 WEMHeight Width Depth Weight Specifications Installation Instructions Safety PrecautionsSpark Arrester Machine GroundingPre-Operation Service Welding Output CablesAWG Connection of Wire Feeders Angle of OperationHigh Altitude Operation Location / VentilationAdditional Safety Precautions Auxiliary PowerInstructions Connection of K930- TIG Module to the WeldmarkDuplex Receptacles Motor StartingElectrical Device USE with the Weldmark Type Common Electrical Devices Possible ConcernsAuxiliary Power While Welding Simultaneous Welding and PowerStandby Power Connections Connection of Weldmark 225 to Premises Wiring Design Features Other FeaturesEngine Features OperationEngine ON-OFF Switch Engine Start Push-Button SwitchWeldmark 225 Approximate Fuel Consumption Welder Controls Function and OperationStarting/Shutdown Instructions Break-in PeriodWire Feed Welding Processes Constant Voltage Welding ProcessStick Constant Current Welding TIG Constant Current WeldingSummary of Welding Processes Stick AutoAccessories K1745-1 Single GAS Cylinder HolderWire Feed Recommended EquipmentStick TIGMaintenance Safety PrecautionsRoutine Maintenance Oil 100 HRS Oil Filter 200 HRSOverspeed is Hazardous Fram CA79Fram G1 Champion RC12YCTroubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Diagrams WEM2239-1 Weldmark Kohler Wiring Diagram CodeConnection of Weldmark 225 to LN-7 & K240 Contactor KIT M17215-2 30-98E How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? Basic CoursePrecaucion Warnung Manufactured by Livcoln Electric Company
Related manuals
Manual 40 pages 19.1 Kb