Lincoln Electric 300 DLX manual 1CONNECTION DIAGRAMSF-1

Page 41

F-1CONNECTION DIAGRAMSF-1

RANGER 300 D & RANGER 300 DLX / LN-25 ACROSS THE ARC CONNECTION DIAGRAM WITH OPTIONAL K857 REMOTE CONTROL

WARNING

Do not operate with panels open.

Disconnect NEGATIVE (-) BATTERY LEAD before servicing.

Do not touch electrically live parts.

Keep guards in place.

Keep away from moving parts.

Only qualified personnel should install,use or service this equipment.

14PIN AMPHENOL

(RANGER 300 DLX ONLY)

TO WORK

ELECTRODE

6 PIN				OPTIONAL K857
AMPHENOL				REMOTE CONTROL
AMPHENOL				REMOTE CONTROL

LN-25

WIRE FEEDER

WORK CLIP LEAD

TO WORK

TO WORK

ELECTRODE CABLE

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE POLARITY SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE RANGE SWITCH TO A WIRE WELDING-CV POSITION.

N.C. IF REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL REMOTE SWITCH IN "REMOTE" POSITION. N.D. ON RANGER 300 DLX, THE WELDING TERMINALS SWITCH MUST BE IN THE "ALWAYS ON" POSITION. N.E. PLACE IDLER SWITCH IN "AUTO" OR "HIGH" IDLE POSITION AS DESIRED.

6-20-97

S23732-1

RANGER 300 D & RANGER 300 DLX / LN-25 ACROSS THE ARC CONNECTION DIAGRAM WITH OPTIONAL K444-1 REMOTE CONTROL

WARNING

Do not operate with panels open.

Disconnect NEGATIVE (-) BATTERY LEAD before servicing.

Do not touch electrically live parts.

Keep guards in place.

Keep away from moving parts.

Only qualified personnel should install,use or service this equipment.

14PIN AMPHENOL

(RANGER 300 DLX ONLY)

TO WORK

ELECTRODE

6 PIN

AMPHENOLOPTIONAL K444-1

REMOTE CONTROL

LN-25

WIRE FEEDER

WORK CLIP LEAD

TO WORK

TO WORK

ELECTRODE CABLE

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE POLARITY SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION RANGE SWITCH TO A WIRE WELDING-CV POSITION.

N.C. IF REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL REMOTE SWITCH IN "REMOTE" POSITION. N.D. ON RANGER 300 DLX, THE WELDING TERMINALS SWITCH MUST BE IN THE "ALWAYS ON" POSITION. N.E. PLACE IDLER SWITCH IN "AUTO" OR "HIGH" IDLE POSITION AS DESIRED.

6-20-97

S23732-2

RANGER 300 D AND 300 DLX

Image 41

Contents Ranger 300 D and 300 DLX California Proposition 65 Warnings SafetyElectric Shock can kill Cylinder may explode if damaged Safety Thank You Table of Contents Vii Ranger 300 D and 300 DLX InstallationHeight Width Depth Weight Location and Ventilation Safety PrecautionsStoring StackingAdditional Safety Precautions PRE-OPERATION Engine ServiceHigh Altitude Operation LiftingFuel Battery ConnectionsEngine Coolant Exhaust DeflectorTotal Combined Length of Electrode and Work Cables Electrical ConnectionsMachine Grounding Welding Cable ConnectionsCircuit Breakers Auxiliary Power RECEPTACLES, PLUGS, and HAND-HELD EquipmentPremises Wiring Figure A.1 Connection of Ranger 300 to Premises WiringGeneral Description Design Features ALL ModelsOperation Additional Safety Precautions Additional FeaturesControls and Settings LimitationsFigure B.1 Output Panel Controls WELDER/GENERATOR Controls Figure B.2 Diesel Engine Controls Engine ControlsBefore Starting the Engine Engine OperationCold Weather Starting and Operation Starting the EngineStopping the Engine USE Diesel Fuel onlyTable B.1 BREAK-IN PeriodWelding Operation Typical Ranger 300 Fuel ConsumptionAC/DC Stick Constant Current Welding Range Setting Actual On Machine Current RangeTable B.2 AC TIG Welding TIG Electrode / Range Settings DC Wire Feed Welding CV with Ranger 300 DLXAC/DC TIG Constant Current Welding After YOU Finish WeldingCarbon ARC Gouging Constant Current DC Wire Feed Welding CV with Ranger 300DTable B.3 Summary of Welding Processes for Ranger 300 DLX Summary of Welding Processes and Machine SettingsTable B.4 Summary of Welding Processes for Ranger 300 D Table B.5 Auxiliary PowerSimultaneous Welding and Power Loads Figure B.5 120V Duplex Receptacles 120/240 Volt Dual Voltage ReceptacleTIG Welding Options Accessories AccessoriesGeneral Options Accessories Accessories Kubota Engine Maintenance Schedule MaintenanceKubota Engine Maintenance Components Table D.1 FrequencyChanging the OIL Routine and Periodic Engine MaintenanceBleeding the Fuel System AIR CleanerTightening the FAN Belt Cooling SystemChecking Electrolyte Level Battery MaintenanceCleaning the Battery Cleaning Welder / Generator MaintenanceOutput Range Selector Polarity Switches Brush Removal and ReplacementHOW to USE Troubleshooting Guide 1TROUBLESHOOTINGE-1 Troubleshooting Wrong position No welding power output Welding Terminals switch 1CONNECTION DIAGRAMSF-1 To Work 2CONNECTION DIAGRAMSF-2Ranger 300 DLX / LN-742 Connection Diagram Connection DiagramsTo Wire Feed Unit Ranger 300 DLX / K930-1 TIG Module / Connection Diagram Ranger 300 D / LN-7 / K240 Contactor KIT Diagram WiringRanger 300 DLXRANGER300 Wiring Diagram Ranger 300 DL11702 DLX DimensionPrint Ranger 300 D and 300 DLX Ranger 300 D and 300 DLX Basic Course How To Read Shop DrawingsPrecaucion Warnung

Related manuals

Manual 34 pages 42.78 Kb