Craftsman 919.724591 Maintenance, Customer Responsibilities, To Check Safety Valve, To Drain Tank

Page 16

MAINTENANCE

Customer Responsibilities

 

Before

Daily

Every

Every

 

 

or after

 

 

each

each

40

100

Yearly

 

use

use

hours

hours

 

 

 

 

Check Safety Valve

●

 

 

 

 

Drain Tank

 

●

 

 

 

Air Filter

 

 

●(1)

●

 

Air compressor pump intake

 

 

 

 

●

and exhaust valves

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1- more frequent in dusty or humid conditions

 

 

 

Unit cycles automatically when

power is on. When performing maintenance, you may be exposed to voltage sources, compressed air, or moving parts. Personal injuries can occur. Before performing any maintenance or repair, disconnect power source from the compressor and bleed off all air pressure.

To ensure efficient operation and longer life of the air compressor unit, a routine maintenance schedule should be prepared and followed. The above routine maintenance schedule is geared to an unit in

a normal working environment operating on a daily basis. If necessary, the schedule should be modified to suit the conditions under which your compressor is used. The modifications will depend upon the hours of operation and the working environment. Compressor units in an extremely dirty and/or hostile environment will require a greater frequency of all maintenance checks.

NOTE: See "Operation" section for the location of controls.

To Check Safety Valve

If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or an explosion.

1.Before starting compressor, pull the ring on the safety valve to make sure that the safety valve operates freely. If the valve

is stuck or does not operate smoothly, it must be replaced with the same type of valve.

To Drain Tank

1.Set the "On/Auto/Off" lever to "OFF".

2.Pull the regulator knob out and turn counterclockwise to set the outlet pressure to zero.

3.Remove the air tool or accessory.

4.Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately 20 psi. Release safety valve ring.

5.Drain water from air tank by opening drain valve (counter- clockwise) on bottom of tank.

A14841

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents AIR Compressor Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8Table of Contents Safety Guidelines Definitions Specification ChartImportant Safety Instructions Operate compressor in a clean, dry well Location away from compressorRestrict the flow of fresh air to Ventilation openingsAttachments & Accessories What Could HappenSafety equipment must be properly Electricity. Like any other electricallyRepairs attempted by unqualified Personnel can result in serious injuryOr attempt maintenance until unit has Result in serious burnsHot for several minutes after operation Do not reach around protective shroudsWhen Transporting Compressor Accessories AccessoriesGlossary Duty CycleAssembly Location of the Air Compressor InstallationPlug Grounded Outlets Grounding Pin Extension Cords Voltage and Circuit ProtectionOperation Description of OperationOutlet Pressure Gauge The outlet Tank Pressure Gauge The tankBreak-in Procedure Pressure Release ValveBefore Each Start-Up Maintenance To Check Safety ValveCustomer Responsibilities To Drain TankAir Filter Inspection and Replacement Air Compressor Pump Intake and Exhaust ValvesMotor Air FilterService and Adjustments To Replace or Clean Check ValveRing Nut Outlet Tube Pressure Relief Check ValveRegulator Tank OutletPressure PressureGauge Quick Connect To Replace RegulatorRegulator Arrow Storage Troubleshooting Being used Check wiring connection Table DES Matières Pleine Garantie D’UN ANMesures DE Sécurité Définitions Tableau DES SpécificationsConsignes DE Sécurité Importantes Conserver ces directives Avertissement Risque dexplosion ou dincendie PréventionRisque Prévention Avertissement Risque déclatementAvertissement Risque de projection dobjets Avertissement Risque de choc électrique Avertissement Risque par inhalationAvertissement Risque relié aux pièces mobiles Avertissement Risque de brûluresAvertissement Risque de chute Risque Avertissement Risque dune utilisation dangereuseAccessoires Cycle DE ServiceAccessoires LexiqueAssemblage Emplacement du compresseur dair Montage DE LappareilRallonges Protection contre la surtension et protection du circuitFamiliarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Utilisation de lappareil Avant le démarrageArrêt de lappareil Procédures de rodageAvant chaque mise en marche Mise en marcheEntretien Responsabilités du clientVérification de la soupape de sûreté Vidange du réservoirFiltre à air Inspection et remplacement MoteurRemplacement ou nettoyage de la soupape de retenue Entretien ET RéglagesLentretien Purgez lair pressurisé du réservoirRemplacement du régulateur Rangement Dépannage SerrerPas Percer, souder ni modifierEst utilisé, ajustez le régulateur Pas Surcharges déclenché 54- FR 55- FR A14841 Get it fixed, at your home or ours

919.724591 specifications

The Craftsman 919.724591 is a highly regarded air compressor designed for both DIY enthusiasts and professionals alike. This versatile tool provides a range of features that make it a go-to choice for various applications, from powering air tools to inflating tires and more.

One of the standout features of the Craftsman 919.724591 is its powerful 6-gallon tank. This tank size strikes an ideal balance between portability and capacity, allowing users to tackle numerous tasks without frequent refueling. With a maximum pressure of 150 PSI, the compressor delivers impressive air power, making it suitable for a range of pneumatic tools, including nail guns, staplers, and paint sprayers.

Equipped with a 2.6 SCFM (Standard Cubic Feet per Minute) at 90 PSI, the Craftsman 919.724591 ensures a steady flow of air for efficient operation. This high performance allows users to complete their projects more quickly and effectively. The compressor also incorporates an oil-free pump, which reduces maintenance needs and ensures that users can rely on it for hassle-free operation. This feature is particularly beneficial for those who prioritize convenience and efficiency.

In terms of portability, the Craftsman 919.724591 does not disappoint. It features a lightweight design and comes with a sturdy handle for easy transportation from one job site to another. The rubber feet further enhance stability during operation, reducing vibrations that could cause misalignment or damage to connected tools.

Safety is another important aspect of the Craftsman 919.724591 design. The air compressor showcases an integrated safety valve that automatically releases pressure if it exceeds safety levels. This feature provides peace of mind, ensuring safe usage even in demanding environments.

The compressor’s user-friendly control panel makes it easy for users of all skill levels to operate. Its clearly labeled gauges allow for straightforward monitoring of pressure levels, ensuring that tools are used within the required specifications.

Overall, the Craftsman 919.724591 is a robust and efficient air compressor that offers a blend of performance, portability, and safety. Its innovative features, such as the oil-free pump, impressive tank capacity, and user-friendly design, make it an excellent choice for anyone seeking reliability and versatility in their air compressor. Whether for home improvement projects or professional tasks, the Craftsman 919.724591 stands out as a dependable tool built to satisfy a wide array of air-powered applications.
Top Page Image Contents