Studer Innotec XPC 1624 Standard setting, Reset value, Battery voltages and absorption time

Page 19
RESET
20 ALARM (Select)

STUDER INNOTEC

XP-COMPACT

 

 

6.1Standard setting

The XP-COMPACT is delivered with the following default setting:

6.1.1Battery voltage

Low voltage

11.6V / 23.2V / 46.4V

Float Charge

13.5V / 27.0V / 54.0V

End of Charge Voltage

14.4V / 28.8V / 57.6V

Equalization

15.3V / 30.6V / 61.2V

Absorption Time:

2 Hours

6.1.2Auxiliary contact

Active in case of defect or manual turn off with the LED 10/11/12/13

6.2Reset value

When the XP-COMPACT is to be connected to a battery or after an interruption (RESET), it is al- ways programmed with these standard settings.

In order to get to these settings during operation you must press the three Push Buttons 20/21/22 simultaneously for a minimum of 2 seconds.

6.3Battery voltages and absorption time

The voltage levels (low voltage, float charge, end of charge and equalization) and the duration of the absorption charge can be changed.

The display of these voltages and the times in the program mode are in accordance with the dia- gram shown below:

6.3.1Table of voltage and timing threshold

 

Low voltage

Float Charge

Absorption

 

Equalization

Absorpt. time

 

LED 13

 

LED 12

 

LED 11

 

LED 10

 

LED 10->13

LED

12V

24V

48V

12V

24V

48V

12V

24V

48V

12V

24V

48V

 

14

12.0

24.0

48.0

13.7

27.4

54.8

15.0

30.0

60.0

15.5

31.0

62.0

4 h

15

11.8

23.6

47.2

13.6

27.2

54.4

14.8

29.6

59.2

15.4

30.8

61.6

3 h

16

11.6

23.2

46.4

13.5

27.0

54.0

14.6

29.2

58.4

15.3

30.6

61.2

2 h

17

11.4

22.8

45.6

13.4

26.8

53.6

14.4

28.8

57.6

15.2

30.4

60.8

1 h

18

11.2

22.4

44.8

13.3

26.6

53.2

14.2

28.4

56.8

15.1

30.2

60.4

0 – 1Min.

The heavy printed values show the standard settings.

6.3.2Set the voltage and timing threshold

The programming is done in accordance with the following steps:

Push and hold down, the Push Button 21 (Program) and the Push Button 19 (Change status) for minimum 2 seconds simultaneously.

With the Push Button 20 (select) select with of the battery level and the absorption time to be changed.

These four red

LED show the function set:

14

10

Over Temp.

Low voltage

LED 13

 

Float charge

LED 12

15

11

Overload

Absorption (End of charge)

LED11

12

Battery

Equalization

LED 10

 

16

Low/High

Absorptions Time

LED 10/11/12/13

 

 

 

 

With the Push Button 19 (Change status) set the

17

13

OFF

18

 

 

desired parameter (voltage or the time) to modify

 

ON/OFF

(LED 14/15/16/17/18). Push Button 19 (Change

 

 

status) to set the desired

value according to the

 

19

(Change status)

 

 

 

21

 

 

 

 

 

 

 

 

 

User manual

 

XP-COMPACT V2.0 E

 

 

18

Image 19
Contents XP-COMPACT V2.0 E XP-COMPACT XPCIntroduction Mounting and installingSummary General InformationMaintenance EC Compliance Technical Data Operating instructions Quality and WarrantyWarranty Disclaimer General InformationSpecial Precautions PrecautionsIntroduction Principle schematicDescription of main functions Connection in parallel Battery connectionsRemote control Solar charge controller optionalProtection cover IP23 Mounting and installingInstallation place FixingProtection cover for the terminals con- nections Connecting panel / Front sideSolar + Connecting the 230Vac-Consumer Appliance AC Output Cabling/wiringPre-installation settings Connection to batteryDisplay and control parameters Connection to Remote controlConnection to Temperature Sensor Temp ControlMarking LED lit LED blinks Light Emitting Diodes LEDTurning Knobs Push buttonsInverter Battery Condition Battery chargerCycle of charge Equalization charging Transfer systemCharging current Set the transfer voltage threshold Fast UPS- Mode for the Transfer SwitchDelayed mode of the Transfer System Solar charge controller optionPower monitor Remote ControlTemperature sensor Remote control plug-inProgramming Battery ConditionFault indicator Remote alarm contact and on/off controlReset value Standard settingBattery voltages and absorption time Principle Program the auxiliary contactExample Disabling some of the XP-COMPACT functions MaintenanceDiagram of the different mode EC ComplianceModel Technical Data