Studer Innotec XPC 1112, XPC 1648, XPC 1624 user manual Special Precautions

Page 5

STUDER INNOTEC

XP-COMPACT

 

 

1.5Precautions

This manual must be readily available for the user at all times. The user must be familiar with the precautions and safety aspects.

During operation of XP-COMPACT, high voltages are generated at the connections and inside of the appliance which could be deadly fatal. Work on the appliance and on the installation should only be carried out by qualified and trained personnel.

The whole installation connected with the XP-COMPACT must comply with the respective valid codes and ordinances.

Persons without the written authorization from STUDER INNOTEC are strictly forbidden to carry out any changes or repairs on the appliances. For authorized changes only original parts are to be used.

The XP-COMPACT may only be used when it has been installed in accordance with these instruc- tions and all parts have been correctly assembled and installed.

On the IN- and OUTPUT points of the XP-COMPACT only the already selected energy sources and consumer appliances should be connected.

In order to carry out any maintenance or repair work on the XP-COMPACT without danger, all connections must be disconnected beforehand.

Caution: Even when a XP-COMPACT has been disconnected from the all connections, at the OUTPUT point there could still be deadly fatal voltages present. To remove these voltages you must switch the XP-COMPACT ON with the ON/OFF switch. After one minute the elec- tronics are discharged and any work can now be safely carried out.

The XP-COMPACT is only suitable for internal use and under no circumstances should it be sub- jected to snow, rain, or any other wet conditions

By installations in motorized vehicles the XP-COMPACT must be protected from water-spray and any other wet conditions..

The XP-COMPACT may only be connected to lead –acid or lead-gel batteries.

Caution: In normal use lead-acid and lead-gel batteries give out explosive gases. Never smoke or allow a spark or flame in the vicinity of batteries. The batteries must always be stored or placed in a well ventilated area, they should be placed in such a way that there is no danger of short circuit- ing through carelessness. Never charge frozen batteries.

The XP-COMPACT is not to be used or sold for life support equipment or applications.

1.6Special Precautions

While working on batteries there should always be a second person close to you or within your voice range, in case help is needed.

Plenty of fresh water and soap must be ready at hand so that in case of acid coming in contact with skin, eyes and clothes, the areas in question can be thoroughly washed.

If acid enters the eyes, you must thoroughly wash the eyes with cold running water for at least 15 minutes. It is recommended that you immediately consult a medical doctor.

Baking powder neutralizes battery acid electrolyte. Always keep some at hand.

Special care must be taken when working with metal tools near or on the batteries. With tools such as screwdrivers, spanners etc. short-circuits can result. Sparks produced by the short-circuit can cause an explosion.

When working on batteries all personal metal items such as rings, necklaces and bracelets must be removed. Batteries are so powerful that short-circuit with these items can melt them and thus cause severe burns. Always follow the battery manufacturer’s instructions.

Under certain conditions the XP-COMPACT or a connected generator can start automatically. While working on an electrical installation you must ensure that these appliances are disconnected beforehand from the installation.

User manual

XP-COMPACT V2.0 E

4

Image 5
Contents XP-COMPACT V2.0 E XP-COMPACT XPCSummary Mounting and installingGeneral Information IntroductionMaintenance EC Compliance Technical Data Warranty Disclaimer Quality and WarrantyGeneral Information Operating instructionsSpecial Precautions PrecautionsDescription of main functions Principle schematicIntroduction Remote control Battery connectionsSolar charge controller optional Connection in parallelInstallation place Mounting and installingFixing Protection cover IP23Solar + Connecting panel / Front sideProtection cover for the terminals con- nections Pre-installation settings Cabling/wiringConnection to battery Connecting the 230Vac-Consumer Appliance AC OutputConnection to Temperature Sensor Temp Connection to Remote controlControl Display and control parametersMarking LED lit LED blinks Light Emitting Diodes LEDInverter Push buttonsTurning Knobs Cycle of charge Battery chargerBattery Condition Charging current Transfer systemEqualization charging Delayed mode of the Transfer System Fast UPS- Mode for the Transfer SwitchSolar charge controller option Set the transfer voltage thresholdTemperature sensor Remote ControlRemote control plug-in Power monitorFault indicator Battery ConditionRemote alarm contact and on/off control ProgrammingBattery voltages and absorption time Standard settingReset value Example Program the auxiliary contactPrinciple Diagram of the different mode MaintenanceEC Compliance Disabling some of the XP-COMPACT functionsModel Technical Data