Skil HD77M manual Cutting Large Sheets, RIP Cuts, RIP Board Guide

Page 11

SM 1619X01288 01-06 1/23/06 8:50 AM Page 11

Allow blade to come to a ! WARNING complete stop before lifting

the saw from cut. Also, never pull the saw backward since blade will climb out of the material and KICKBACK will occur.

Turn saw around and finish the cut in the normal manner, sawing forward. If corners of your pocket cut are not completely cut through, use a jigsaw or hand saw to finish the corners.

CUTTING LARGE SHEETS

Large sheets and long boards sag or bend, depending on support. If you attempt to cut without leveling and properly supporting the piece, the blade will tend to bind, causing KICK- BACK and extra load on the motor (Fig. 8).

Support the panel or board close to the cut, as shown in (Fig. 9). Be sure to set the depth of the cut so that you cut through the sheet or board only and not the table or work bench. The two- by-fours used to raise and support the work should be positioned so that the broadest sides support the work and rest on the table or bench. Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by-fours on the floor and secure.

WRONG

FIG. 8

RIGHT

FIG. 9

RIP CUTS

The combination blade provided with your saw is for both cross cuts and rip cuts. Ripping is cutting lengthwise with the grain of the wood. Rip cuts are easy to do with a rip fence (Fig. 10). Rip Fence is available as an accessory (not included). To attach fence, insert fence through slots in foot to desired width as shown and secure with the wing nut (not included).

 

 

FIG. 10

DESIRED

WIDTH OF CUT

 

 

RIP BOARD GUIDE

When rip cutting large sheets, the rip fence may not allow the desired width of cut. Clamp or nail a straight piece of 1" (25 mm) lumber to the sheet as a guide (Fig. 11). Use the right side of the foot against the board guide.

RIP

FIG. 11

 

BOARD

 

GUIDE

 

 

DESIRED

RIP FENCE

LINE

OF CUT

-11-

Image 11
Contents See Voir Ver la página Read Before Using Lire avant usageImportante Call Toll Free forKeep your work area clean and well lit Power Tool Safety RulesElectrical Safety Personal SafetyTool Use and Care Safety Rules for Circular SawsService VARI-TORQUE Clutch Causes and Operator Prevention KickbackProtruding blade may cut objects that can cause Kickback Symbols Maximum Capacities Functional Description and SpecificationsCircular Saws VARI-TORQUE Clutch AssemblyAttaching the Blade Cutting Angle Check Depth AdjustmentBevel Adjustment Operating InstructionsPocket Cuts SwitchGeneral Cuts Cutting MASONRY/METALRIP Board Guide Cutting Large SheetsRIP Cuts Cleaning MaintenanceAccessories Conservez CES Instructions Règles de Sécurité GénéralesAire de travail Sécurité des personnes Sécurité électriqueLa réparation des outils électriques doit être confiée Consignes de sécurité pour scies circulairesUtilisation et entretien des outils RéparationEmbrayage VARI-TORQUE Causes ET PRÉVENTION, PAR Lopérateur DU RebondLe plomb provenant des peintures à base de plomb Symboles Semelle Description fonctionnelle et spécificationsScies circulaires Embrayage « VARI-TORQUE » AssemblageMontage DE LA Lame Réglage DE LA Coupe EN Biseau Consignes de fonctionnementRéglage DE LA Profondeur DE Coupe Vérification DE L’ANGLE DE CoupeCoupes EN Guichet InterrupteurCoupes Régulierès Sciage DES Matériaux DE Maçonnerie ET DES MétauxUtilisation D’UNE Planche Comme Guide DE Refente Coupe DE Grandes FeuillesCoupes DE Refente Paliers EntretienLubrification DE L’OUTIL Balais DE Charbon20 AMP., 125 Volts AccessoiresSeguridad personal Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad eléctricaServicio Normas de seguridad para sierras circularesEmbrague DE PAR Motor Variable Causas DEL Retroceso Y SU Prevencion POR EL OperadorSM 1619X01288 01-06 1/23/06 850 AM De Ni-Cd SímbolosMango Auxiliar Descripción funcional y especificacionesSierras circulares Capacidades máximasProtector Superior EnsamblajeColocacion DE LA Hoja Embrague DE PAR Motor VariableGuía DE Línea Instrucciones de funcionamientoAjuste DE Profundidad Ajuste DE InclinaciónCorte DE Mamposteria Y Metal Guía DE InterruptorCortes Generales Movimiento libre del protector inferiorIncorrecto Correcto Corte DE Planchas GrandesCortes AL Hilo TABLERO-GUIA Para Cortar AL HiloLimpieza MantenimientoTraba POR Giro DE 20 AMP, 125 Volt AccesoriosSM 1619X01288 01-06 1/23/06 850 AM Remarques Notas Limited Warranty of Skil HD Heavy Duty Portable Power Tools