Skil HD77M manual Accessories

Page 13

SM 1619X01288 01-06 1/23/06 8:50 AM Page 13

TWIST-TO-LOCK CONNECTOR INSTRUCTIONS FOR MODELS HD77 & HD77M CODE 72 ONLY

20 AMP, 125 VOLT “TWIST-TO-LOCK”

The Model HD77 & HD77M code 72 is equipped with a “Twist-To-Lock” male connector as shown. Use only a 3-wire extension cord which has a mating “Twist-To-Lock” female connector on one end and a 3-prong grounding plug on the other end. (See Electrical Safety section on page 2 for grounding information.)

Accessories

!WARNING If an extension cord is necessary, a cord with

adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

25

50

100

150

15

30

60

120

 

3-6

 

 

 

 

 

 

 

 

18

16

16

14

0.75

0.75

1.5

2.5

6-8

18

16

14

12

0.75

1.0

2.5

4.0

8-10

18

16

14

12

0.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

*

Blade

(*= standard equipment)

*

Wrench

(**= optional accessories)

**Carrying case

**Rip Fence

**Non-marring overshoe

-13-

Image 13
Contents Importante Read Before Using Lire avant usageCall Toll Free for See Voir Ver la páginaElectrical Safety Power Tool Safety RulesPersonal Safety Keep your work area clean and well litService Safety Rules for Circular SawsTool Use and Care VARI-TORQUE Clutch Causes and Operator Prevention KickbackProtruding blade may cut objects that can cause Kickback Symbols Circular Saws Functional Description and SpecificationsMaximum Capacities Attaching the Blade AssemblyVARI-TORQUE Clutch Bevel Adjustment Depth AdjustmentOperating Instructions Cutting Angle CheckGeneral Cuts SwitchCutting MASONRY/METAL Pocket CutsRIP Cuts Cutting Large SheetsRIP Board Guide Cleaning MaintenanceAccessories Aire de travail Règles de Sécurité GénéralesSécurité des personnes Sécurité électrique Conservez CES InstructionsUtilisation et entretien des outils Consignes de sécurité pour scies circulairesRéparation La réparation des outils électriques doit être confiéeEmbrayage VARI-TORQUE Causes ET PRÉVENTION, PAR Lopérateur DU RebondLe plomb provenant des peintures à base de plomb Symboles Scies circulaires Description fonctionnelle et spécificationsSemelle Montage DE LA Lame AssemblageEmbrayage « VARI-TORQUE » Réglage DE LA Profondeur DE Coupe Consignes de fonctionnementVérification DE L’ANGLE DE Coupe Réglage DE LA Coupe EN BiseauCoupes Régulierès InterrupteurSciage DES Matériaux DE Maçonnerie ET DES Métaux Coupes EN GuichetCoupes DE Refente Coupe DE Grandes FeuillesUtilisation D’UNE Planche Comme Guide DE Refente Lubrification DE L’OUTIL EntretienBalais DE Charbon Paliers20 AMP., 125 Volts AccessoiresArea de trabajo Normas de seguridad para herramientas mecánicasSeguridad eléctrica Seguridad personalServicio Normas de seguridad para sierras circularesEmbrague DE PAR Motor Variable Causas DEL Retroceso Y SU Prevencion POR EL OperadorSM 1619X01288 01-06 1/23/06 850 AM De Ni-Cd SímbolosSierras circulares Descripción funcional y especificacionesCapacidades máximas Mango AuxiliarColocacion DE LA Hoja EnsamblajeEmbrague DE PAR Motor Variable Protector SuperiorAjuste DE Profundidad Instrucciones de funcionamientoAjuste DE Inclinación Guía DE LíneaCortes Generales Guía DE InterruptorMovimiento libre del protector inferior Corte DE Mamposteria Y MetalCortes AL Hilo Corte DE Planchas GrandesTABLERO-GUIA Para Cortar AL Hilo Incorrecto CorrectoLimpieza MantenimientoTraba POR Giro DE 20 AMP, 125 Volt AccesoriosSM 1619X01288 01-06 1/23/06 850 AM Remarques Notas Limited Warranty of Skil HD Heavy Duty Portable Power Tools