Skil 4580, 4540, 4480 manual Safety Rules for Jigsaws, Service

Page 3

Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.

Such preventive safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. Any alteration or modification is a misuse and may result in a dangerous condition.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Develop

a periodic maintenance schedule for your tool.

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

Service

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. For example: internal wires may be misplaced or pinched, safety guard return springs may be improperly mounted.

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

Safety Rules for Jigsaws

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. Do not drill, fasten or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit breakers feeding this worksite.

Never leave the trigger locked "ON". Before plugging the tool in, check that the trigger lock is "OFF". Accidental start-ups could cause injury.

Be aware of the location and setting of the switch "Lock-ON" button. If the switch is locked "ON" during the use, be ready for emergency situations to switch it "OFF", by

first pulling the trigger then immediately releasing it without pressing the "Lock-ON" button.

Keep hands away from cutting area. Do not reach under the material being cut. The proximity of the blade to your hand is hidden from your sight.

Keep hands from between the gear housing and saw blade holder. The reciprocating blade holder can pinch your fingers.

Do not use dull or damaged blades. Bent blade can break easily or cause kickback.

Before starting to cut, turn tool "ON" and allow the blade to come to full speed.

Tool can chatter or vibrate if blade speed is too slow at beginning of cut and possibly kickback.

-3-

Image 3
Contents Voir Ver página For EnglishSee ¿Habla español?Work Area Power Tool Safety RulesElectrical Safety Personal SafetyService Safety Rules for JigsawsHot after prolonged use Symbols Length Wood Functional Description and SpecificationsJigsaws StrokeOperating Instructions AssemblyBlade Storage Compartment Dust ExtractionSITE-LIGHT Model 4580 only Cutting with a Straightedge Cutting TipsPlunge Cutting Bevel or Angle CuttingMetal Cutting Attaching RIP Fence Straight CuttingCircle Cutting Nail Blade Must be in Alignment with Nail Maintenance AccessoriesCleaning Sécurité des personnes Règles de Sécurité GénéralesAire de travail Sécurité électriqueRéparation Règles de sécurité concernant les scies sauteusesLe plomb provenant des peintures à base de plomb Symboles Scies sauteuses Description fonctionnelle et spécificationsAssemblage Consignes de fonctionnementPose de la lame Modèles À Mouvement Orbital Compartiment DE Rangement DE LameExtraction DE Poussière Éclairage D’APPOINT SITE-LIGHTSciage Avec Guide DE Coupe Conseils PratiquesModèles À Chantournage 4540 et 4580 seulementVIS Semelle Languette DE Blocage Coupe EN PlongéeSciage EN Biais OU EN Biseau Coupe Dans LES MétauxCoupe Circulaire Assemblage DU Guide DE RefenteCoupe Rectiligne Vis FigClou Accessoires EntretienNettoyage Seguridad personal Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad eléctricaServicio Normas de seguridad para sierras de vaivénPage De Ni-Cd SímbolosDescripción funcional y especificaciones Sierras de vaivénCapacidades Maximas Instrucciones de funcionamiento EnsamblajeModelos DE Acción Orbital Extraccion DE PolvoENCENDIDO= LUZ SITE-LIGHTCorte CON Regla Recta Medelos 4540 y 4580 solamentePunta DE LA Base Corte Mediante Descenso VerticalCorte Inclinado O EN Ángulo Corte DE MetalTOPE-GUIA Para Cortar AL Hilo Guia DE Corte Circular Corte RectoCorte Circular Clavo LA Hoja Debe Estar Alineada CON EL Clavo Mantenimiento AccesoriosLimpieza Page Remarques Notas