Harbor Freight Tools 67853 manual Pre-Start Checks, Starting the Engine, Injury from Fire

Page 31

Operation

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before

set up or use of this product.

Pre-Start Checks

Inspect engine and equipment looking for damaged, loose, and missing parts before set up and starting. If any problems are found, do not use equipment until fixed properly.

Checking and Filling Engine Oil

CAUTION! Your Warranty is VOID if the engine’s crankcase is not properly filled with oil before each use. Before each use, check the oil level. Do not run the engine with low or no engine oil. Running the engine with no or low engine oil WILL permanently damage the engine.

1.Make sure the engine is stopped and is level.

2.Close the Fuel Valve.

3.Clean the top of the Dipstick and the area around it. Remove the Dipstick by threading it counterclockwise, and wipe it off with a clean lint free rag.

Checking and Filling Fuel

WARNING! TO PREVENT SERIOUS

INJURY FROM FIRE:

Fill the fuel tank in a well-ventilated area away from ignition sources. If the engine is hot from use, shut the engine off and wait for it to cool before adding fuel. Do not smoke.

1.Clean the Fuel Cap and the area around it.

2.Unscrew and remove the Fuel Cap.

3.If needed, fill the Fuel Tank to about 1 inch under the fill neck of the Fuel Tank with 87 octane or higher unleaded gasoline.

Note: Do not use gasoline containing more than 10% ethanol (E10). Do not use E85 ethanol.

Note: Do not use gasoline that has been stored in a metal fuel container or a dirty fuel container. It can cause particles to enter the carburetor, affecting engine performance and/or causing damage.

4.Then replace the Fuel Cap.

5.Wipe up any spilled fuel and allow excess to evaporate before starting engine. To prevent FIRE, do not start the engine while the smell of fuel hangs in the air.

Starting the Engine

Before Starting the Engine

Before starting the engine:

Full level

Full level

a. Follow the Set Up Instructions

in the equipment manual to

prepare the equipment.

b. Inspect the equipment and engine.

c. Fill the engine with the proper amount

4.Reinsert the Dipstick without threading it in and remove it to check the oil level. The oil level should be up to the full level as shown above.

5.If the oil level is at or below the low mark add the appropriate type of oil until the oil level is at the proper level. SAE 10W‑30 oil is recommended for general use. (The SAE Viscosity Grade chart on page 14 in the Service section shows other viscosities to use in different average temperatures.)

6.Thread the dipstick back in clockwise.

CAUTION! Do not run the engine with too little oil. The engine will be permanently damaged.

and type of both fuel and oil.

d. Read the Equipment Operation

section in the equipment manual.

Page 8

For Engine technical questions, please call 1-800-520-0882.

Horizontal Engines

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Minutes Using an engine indoors can Kill YOUPage Symbol Property or Statement Symbol DefinitionsSet up Precautions Safety WarningsCarbon Monoxide Hazard Using an engine indoors can Kill Engine Precautions Operating PrecautionsYOU in Minutes Air Compressor Safety Warnings Service PrecautionsEngine Controls Break-In Compressor AssemblySet up Mounting to a Truck bedDescription Function Spray Gun Portable SetupDescription Function To Start and Use the Compressor Using the CompressorOperation Before starting the CompressorStart For Manual StartMaintenance Break-in Period For technical questions, please call 1-800-444 Adding Oil Maintenance ProceduresCompressor Pump Oil Maintenance MaintenanceDraining Moisture from the Tank Air Filter MaintenanceAdjusting Belt Tension Changing OilProblem Possible Causes Likely Solutions TroubleshootingPlease Read the Following Carefully Part Description Qty Pump Parts ListPump Assembly Diagram Tank Parts List Tank Assembly Diagram Limited 90 Day Warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800 Specifications212, 346 and 420 cc Horizontal Engines Description 68120 68136 68306 Eye Injury. Wear ANSI-approved Use only accessories that are recommended by Harbor Do not Overfill RefuelingAir Filter Engine SwitchTo Prevent Serious Injury Battery Setup InstructionsCable Gauge Maximum 12′Starting the Engine Pre-Start ChecksInjury from Fire Manual Start Turn the Engine Switch onBreak-in Period Stopping the EngineElectric Start if equipped Turn the Engine Switch to StartOFF To Prevent Serious Injury from Equipment Failure Cleaning, Maintenance, and Lubrication ScheduleService To Prevent Serious Injury from Accidental StartingCleaning Air Filter Element MaintenanceEngine Oil Change Recommended Spark Plugs Storage10% ethanol E15, E20, E85, etc TroubleshootingProblem Possible Causes Probable Solutions Do not use gasoline with more thanCompression Related section Use Engine will not startWarranties Limited 90 Day WarrantyEmission Control System Warranty Manufacturer’s Warranty CoverageOwner’s Warranty Responsibilities 68120 212cc Parts List and Diagram 68120 212cc Parts List and Diagram 68121 212cc Parts List and Diagram 102 68136 346cc Parts List and Diagram 68136 346cc Parts List and DiagramPart Description Qty 68306 420cc Parts List and Diagram68306 420cc Parts Item 68120 / 68121 212cc Mounting Hole DiagramsItem 68136 346cc and Item 68306 420cc 16-24UNF Power Take-Off DiagramsMission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800

67853 specifications

Harbor Freight Tools is widely recognized for providing a variety of high-quality tools at competitive prices, and the model 67853 is no exception. This tool combines functionality, durability, and affordability, making it a popular choice among both amateur and professional users.

The Harbor Freight Tools 67853 is a 20" tool chest that stands out for its robust construction and ample storage capabilities. This tool chest features double-walled steel construction, ensuring that it can withstand the rigors of a busy workshop or garage. Its powder-coated finish not only enhances its aesthetic appeal but also provides added protection against rust and corrosion, ensuring that the chest maintains its integrity over time.

One of the key features of the 67853 is the abundance of storage space it offers. The chest is designed with multiple drawers that provide easy access to tools and supplies. Each drawer is equipped with ball-bearing slides that ensure smooth opening and closing, minimizing the risk of wear and tear over time. The drawers are designed to hold a significant amount of weight, allowing users to store a variety of tools, from hand tools to power equipment.

The organization is made easy with the inclusion of padded drawer liners that help keep tools in place, preventing them from sliding around during opening and closing. This thoughtful design feature is particularly beneficial when working in a fast-paced environment where efficiency is key. Furthermore, the top section of the chest is perfect for displaying frequently used tools or storing small items for easy access.

Safety and security are also prioritized with the Harbor Freight Tools 67853. The chest comes equipped with a central locking system that secures all drawers simultaneously, protecting valuable tools from theft and ensuring that everything is kept in its designated place. This added layer of security is vital for professionals who rely on their tools for daily operations.

Another notable aspect of the 67853 is its mobility. The chest is fitted with sturdy casters, allowing users to easily move it around the workshop or garage as needed. This mobility is coupled with a solid locking mechanism that keeps the chest stable when in use, ensuring it won't roll away unexpectedly.

In terms of aesthetics, the Harbor Freight Tools 67853 features a sleek design that will complement any workspace. The glossy finish and minimalist lines provide a professional look that is appealing to users across all fields.

Overall, the Harbor Freight Tools 67853 offers excellent value for users seeking a reliable and stylish tool chest that fulfills various storage needs. Its durable construction, ample storage, and thoughtful design make it a top choice in the market, catering to both hobbyists and seasoned professionals alike.
Top Page Image Contents