Harbor Freight Tools 67853 Mounting to a Truck bed, Assembly, Break-In Compressor, Connection

Page 7

Set up

The emission control system for this Compressor’s Engine is warranted for standards set by the U.S. Environmental Protection Agency and by the California Air Resources Board (also known as CARB). For warranty information, refer to the engine manual.

Mounting to a Truck bed

1.Before mounting, if needed, reinforce the area with plywood or steel plating.

2.With assistance, move the compressor to the truck bed location and mark the floor of the truck bed through the holes in the compressor’s feet. Check for any hidden wiring or cables and adjust the location for the holes as needed. Then, temporarily set the compressor aside.

3.Drill the four 1/2” diameter holes through the truck bed and any reinforcing materials.

4.Set the compressor back in place, and align the foot holes with the pre-drilled holes. Use four 1/2” diameter, bolts, washers and lock washers (all not included) to secure the compressor in place.

Assembly

To install the Air Filter Assembly (84), fit the Connector into the Air Filter Assembly and slide the assembly into the hole on the side of the First Stage Cylinder Head (61). Secure in place with the Wing Nut.

Break-In Compressor

Air Filter

Second Stage

 

Assembly (84)

Cylinder Head

First Stage

Wing Nut

Connector

(21)

 

Cylinder Head

 

 

 

 

(61)

Break in the new Air Compressor as follows:

a.Make sure the engine is off. Open the air outlet valve on the left side of the tank.

b.Check all fluid levels in the engine and pump.

c.Start the engine following the General Operating Instructions.

d.Let the unit run for 30 minutes. Air will expel freely through the Coupler.

e.Turn OFF the engine.

f.Remove the male coupler.

Connection

Connect a regulator valve, an in-line shut off valve and a 1/2” NPT air hose (all sold separately) to the Quick Coupler. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.

Note: An in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. The shutoff valve should be a ball valve because it can be closed quickly.

1.Depending on the tool which you will be using with this compressor, you may need to incorporate additional components, such as an in-line oiler, a filter, or a dryer (all sold separately). Consult your air tool’s manual for needed accessories. See Typical Air Line Setup charts on the following pages. This is a truckbed compressor, so use the portable setup as a model.

Item 67853

For technical questions, please call 1-800-444 3353.

Page 5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Minutes Using an engine indoors can Kill YOUPage Symbol Property or Statement Symbol DefinitionsSet up Precautions Safety WarningsCarbon Monoxide Hazard Using an engine indoors can Kill Engine Precautions Operating PrecautionsYOU in Minutes Air Compressor Safety Warnings Service PrecautionsEngine Controls Break-In Compressor AssemblySet up Mounting to a Truck bedDescription Function Spray Gun Portable SetupDescription Function To Start and Use the Compressor Using the CompressorOperation Before starting the CompressorStart For Manual StartMaintenance Break-in Period For technical questions, please call 1-800-444 Adding Oil Maintenance ProceduresCompressor Pump Oil Maintenance MaintenanceDraining Moisture from the Tank Air Filter MaintenanceAdjusting Belt Tension Changing OilProblem Possible Causes Likely Solutions TroubleshootingPlease Read the Following Carefully Part Description Qty Pump Parts ListPump Assembly Diagram Tank Parts List Tank Assembly Diagram Limited 90 Day Warranty Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800 Specifications212, 346 and 420 cc Horizontal Engines Description 68120 68136 68306 Eye Injury. Wear ANSI-approved Use only accessories that are recommended by Harbor Do not Overfill RefuelingAir Filter Engine SwitchTo Prevent Serious Injury Battery Setup InstructionsCable Gauge Maximum 12′Starting the Engine Pre-Start ChecksInjury from Fire Manual Start Turn the Engine Switch onBreak-in Period Stopping the EngineElectric Start if equipped Turn the Engine Switch to StartOFF To Prevent Serious Injury from Equipment Failure Cleaning, Maintenance, and Lubrication ScheduleService To Prevent Serious Injury from Accidental StartingCleaning Air Filter Element MaintenanceEngine Oil Change Recommended Spark Plugs Storage10% ethanol E15, E20, E85, etc TroubleshootingProblem Possible Causes Probable Solutions Do not use gasoline with more thanCompression Related section Use Engine will not startWarranties Limited 90 Day WarrantyEmission Control System Warranty Manufacturer’s Warranty CoverageOwner’s Warranty Responsibilities 68120 212cc Parts List and Diagram 68120 212cc Parts List and Diagram 68121 212cc Parts List and Diagram 102 68136 346cc Parts List and Diagram 68136 346cc Parts List and DiagramPart Description Qty 68306 420cc Parts List and Diagram68306 420cc Parts Item 68120 / 68121 212cc Mounting Hole DiagramsItem 68136 346cc and Item 68306 420cc 16-24UNF Power Take-Off DiagramsMission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800

67853 specifications

Harbor Freight Tools is widely recognized for providing a variety of high-quality tools at competitive prices, and the model 67853 is no exception. This tool combines functionality, durability, and affordability, making it a popular choice among both amateur and professional users.

The Harbor Freight Tools 67853 is a 20" tool chest that stands out for its robust construction and ample storage capabilities. This tool chest features double-walled steel construction, ensuring that it can withstand the rigors of a busy workshop or garage. Its powder-coated finish not only enhances its aesthetic appeal but also provides added protection against rust and corrosion, ensuring that the chest maintains its integrity over time.

One of the key features of the 67853 is the abundance of storage space it offers. The chest is designed with multiple drawers that provide easy access to tools and supplies. Each drawer is equipped with ball-bearing slides that ensure smooth opening and closing, minimizing the risk of wear and tear over time. The drawers are designed to hold a significant amount of weight, allowing users to store a variety of tools, from hand tools to power equipment.

The organization is made easy with the inclusion of padded drawer liners that help keep tools in place, preventing them from sliding around during opening and closing. This thoughtful design feature is particularly beneficial when working in a fast-paced environment where efficiency is key. Furthermore, the top section of the chest is perfect for displaying frequently used tools or storing small items for easy access.

Safety and security are also prioritized with the Harbor Freight Tools 67853. The chest comes equipped with a central locking system that secures all drawers simultaneously, protecting valuable tools from theft and ensuring that everything is kept in its designated place. This added layer of security is vital for professionals who rely on their tools for daily operations.

Another notable aspect of the 67853 is its mobility. The chest is fitted with sturdy casters, allowing users to easily move it around the workshop or garage as needed. This mobility is coupled with a solid locking mechanism that keeps the chest stable when in use, ensuring it won't roll away unexpectedly.

In terms of aesthetics, the Harbor Freight Tools 67853 features a sleek design that will complement any workspace. The glossy finish and minimalist lines provide a professional look that is appealing to users across all fields.

Overall, the Harbor Freight Tools 67853 offers excellent value for users seeking a reliable and stylish tool chest that fulfills various storage needs. Its durable construction, ample storage, and thoughtful design make it a top choice in the market, catering to both hobbyists and seasoned professionals alike.
Top Page Image Contents