Porter-Cable RS830 instruction manual Compound Miter Cutting, Out-Ripping, In-Ripping

Page 26

COMPOUND

MITER CUTTING

Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation are similar to miter cutting except that the blade is first tilted to the desired angle on the bevel scale before it is clamped in place. Fig. 79, shows a compound miter cutting operation on the radial saw.

RIPPING

IMPORTANT: In certain applications it may be necessary to use two push sticks, and/or featherboards. Also, if a push stick or other feeding device is necessary to assist in the feeding of material, make certain it is conveniently located so it may be reached easily without having to stretch or reach near the blade.

Ripping involves making a lengthwise cut through a board along the grain. When ripping, the track arm is clamped at “0” on the miter scale. The yoke is then positioned and clamped so that the blade is parallel to the fence in either the inboard or outboard position. When feeding the material, one edge rides against the fence while the flat side of the board rests on the table. The guard should be lowered on the in-feed side until it almost touches the workpiece, as shown in Figs. 80 and 81, to act as a holddown. The splitter and anti-kickback fingers (A) Fig. 80, should be adjusted as described under the section

“A DJU STIN G S PLIT TER AN D A NTI- KIC KBA CK FINGERS” in this manual. The operators hands should always be well away from and to the side of the blade. When ripping narrow work, always use a push stick as shown in Fig. 81, to push the work between the fence and blade. The workpiece must have one straight edge to follow the fence. If board is bowed, place hollow side down. The cutting-head clamp knob should be securely tightened for all ripping operations.

WARNING: THE MATERIAL MUST NEVER BE FED INTO THE OUTFEED END OF THE BLADE GUARD.

OUT-RIPPING

Out-ripping involves all of the general conditions stated above. The yoke is clamped at right angle to the track arm with the blade guard facing the front of the machine. The cutting-head is positioned on the out-rip scale to the desired setting and clamped in position. The workpiece is fed from the left side of the saw. Fig. 80, shows a typical out-ripping operation on the radial saw.

IN-RIPPING

In-ripping involves all of the general conditions stated under RIPPING. The yoke is clamped at right angle to the track arm with the blade guard facing the rear of the machine. The cutting-head is positioned on the in-rip scale to the desired setting and clamped in position. The workpiece is fed from the right side of the saw. Fig. 81, shows a typical in-ripping operation on the radial saw.

Fig. 79

A

Fig. 80

Fig. 81

WARNING: WHEN RIPPING WORK LESS THAN FOUR INCHES WIDE, A PUSH STICK SHOULD BE USED TO COMPLETE THE FEED (SEE FIGS. 81 & 83)

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Professional Radial Arm Saw General Safety Rules Additional Safety Rules for Radial ARM Saws Avoid Kickback byGrounding Instructions Power ConnectionsMotor Specifications Qualified Electrician Check the ReceptacleChanging Voltage Extension CordsUnpacking and Cleaning Operating InstructionsRadial ARM SAW Parts Table Board Parts 811 912Wrench Hook to SAW Base AssemblyLegs to SAW Base Disconnect Machine from Power Source Removing Blade and Blade Guard from SAWTable Supports Page HS a Table Board Clamps and Table Boards Adjusting Checking SAW Blade Travel Square to FenceDisconnect Machine from Power Source Page Checking and Adjusting SAW Blade Square To Table Removing Heeling in SAW Blade CUTAdjusting IN/OUT RIP Scale FJ aAssembling Blade and Blade Guard to Machine Tongue on Guard Seats Into Groove of CUTTING-HEADCutting Into Table Boards Fastening SAW to the FloorStarting and Stoping Radial ARM SAW Locking Switch OFF PositionAdjusting Ball Bearings Against Track Adjusting Tension on Elevating Column Changing Position of Track ARM Clamping HandleTable SURFACE, Raise Track ARM Changing Position of Bevel Clamp HandleChanging Position of Yoke Clamp Handle Positive Stop Bevel Index Adjusting Splitter and ANTI-KICKBACK FingersPositive Stop Yoke Index Explanation of Operating Controls CB KAuxiliary Table Board Facing OperationsOUT-RIPPING Compound Miter CuttingRipping IN-RIPPINGMaintenance Overload ProtectionPush Stick Constructing a Push StickPage Accessories PARTS, Service or Warranty Assistance
Top Page Image Contents