Porter-Cable 7313 manual Belt Sander Safety Rules, Service

Page 3

SM 2610929106 3-05 3/15/05 10:33 PM Page 3

job better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control. Any alteration or modification is a misuse and may result in a dangerous condition.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools. Develop a periodic maintenance schedule for your tool.

Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

Service

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. For example: internal wires may be misplaced or pinched, safety guard return springs may be improperly mounted.

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts.

Belt Sander Safety Rules

Hold tool by insulated gripping surfaces when performing a operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

Never leave the trigger locked “ON”. Before plugging the tool in, check that the trigger lock is “OFF”. Accidental start-ups

could cause injury.

Unplug the sander before changing accessories. Accidental start-ups may occur if sander is plugged in while changing an accessory.

Keep your fingers and clothing away from the belt. They could get cut or wedged between the pulley, belt and motor housing.

Properly adjust tracking of belt to avoid it overhanging the housing. A running belt overhanging its housing can cause severe lacerations.

Be aware of the location and setting of the Switch "Lock-ON" Button. If the switch

is locked "ON", be ready for emergency situations to switch it "OFF", by first pulling the trigger then immediately releasing it without pressing the "Lock-ON" button.

Keep the cord to the side away from pulleys. The cord can be dragged into belt housing and become entangled with the pulleys.

Clamp or secure workpiece when sanding. Clamping the workpiece prevents it from being ejected from under the sander and leaves both hands to control the tool.

Clamp or secure sander if it is inverted and bench mounted for use as a table sander. Always use edge stop or guide when sanding short or small workpieces.

Fingers or clothing can be dragged into pulley and housing area.

Do not wet sand with this sander. Liquids entering the motor housing is an electrical shock hazard.

If your tool is equipped with a dust bag, empty it frequently and after completion

-3-

Image 3
Contents For English Parlez-vous français? SeeVoir Ver página Work Area Power Tool Safety RulesElectrical Safety Personal SafetyService Belt Sander Safety RulesSM 2610929106 3-05 3/15/05 1033 PM Symbols Belt Sander Functional Description and SpecificationsOperating Instructions AssemblyType of Material Remarks Grit Size Adjusting the AUTO-TRACK SystemAUTO-TRACK System Selecting the Sanding BeltSanding Tips Maintenance AccessoriesCleaning Conservez CES Instructions Règles de Sécurité GénéralesRéparation Consignes de sécurité de la ponceuse à courroieLe plomb provenant des peintures à base de plomb Symboles Ponceuse à courroie Description fonctionnelle et spécificationsConsignes de fonctionnement AssemblageType DE Matériau Remarques Numéro DU Grain AUTO-ALIGNEMENTRéglage DE L’AUTO-ALIGNEMENT Choix DE Courroie DE PonçageConseils pratiques Accessoires EntretienNettoyage Seguridad personal Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad eléctricaServicio Normas de seguridad para lijadoras de correaSM 2610929106 3-05 3/15/05 1033 PM De Ni-Cd SímbolosLijadoras de correa Descripción funcional y especificacionesPara Instalar LA Correa EnsamblajeInstrucciones de funcionamiento Para Quitar LA CorreaTamaño DEL Grano Sistema Automatico DE Control DE LA TrayectoriaSeleccion DE LA Correa Para Lijar Tipo DE MaterialConsejos para lijar Mantenimiento AccesoriosLimpieza SM 2610929106 3-05 3/15/05 1033 PM Remarques Notas SM 2610929106 3-05 3/15/05 1033 PM