Porter-Cable 36-678, 36-649, 36-675, 36-679 instruction manual Additional Safety Rules for Table Saws

Page 5

ADDITIONAL SAFETY RULES FOR TABLE SAWS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured, and working correctly.

5.KICKBACK IS THE NATURAL TENDENCY OF THE WORKPIECE TO BE THROWN BACK AT THE OPERATOR when the workpiece initially contacts the blade or if the workpiece pinches the blade. Kickback is dangerous and can result in serious injury.

AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and spreader for every possible operation, including all through sawing.

D.pushing the workpiece past the saw blade prior to release.

E.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

F.using featherboards when the anti-kickback device cannot be used.

G.never sawing a large workpiece that cannot be controlled.

H.never using the fence as a guide when crosscutting.

I.never sawing a workpiece with loose knots or other flaws.

6.ALWAYS USE GUARDS, SPLITTER, AND ANTI- KICKBACK FINGERS whenever possible.

7.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out. After cutting, turn the machine off. After the blade has come to a complete stop, remove all debris.

8.NEVER START THE MACHINE with the workpiece against the blade.

9.NEVER run the workpiece between the fence and a moulding cutterhead.

10.CUTTING THE WORKPIECE WITHOUT THE USE OF A FENCE OR MITER GAUGE IS KNOWN AS “FREEHAND” CUTTING. NEVER perform “free-hand” operations. Use either the fence or miter gauge to position and guide the workpiece.

11.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

12.CUTTING COMPLETELY THROUGH THE WORK- PIECE IS KNOWN AS “THROUGH-SAWING”. Ripping and cross-cutting are through-sawing operations. Cutting with the grain is ripping. Cutting across the grain is cross-cutting. Use a fence or fence system for ripping. DO NOT use a fence or fence system for cross-cutting. Instead, use a miter gauge. USE PUSH STICK(S) for ripping a narrow workpiece.

13.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

14.KEEP ARMS, HANDS, AND FINGERS away from the blade.

15.NEVER have any part of your body in line with the path of the saw blade.

16.NEVER REACH AROUND or over the saw blade.

17.NEVER attempt to free a stalled saw blade without first turning the machine “OFF”.

18.PROPERLY SUPPORT LONG OR WIDE workpieces.

19.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

20.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

21.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

22.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Shown Contractor’s SawImportant Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are DOING, General Safety RulesImportant Safety Instructions Properly Support Long or Wide workpieces Additional Safety Rules for Table SawsGrounding Instructions Power ConnectionsMotor Specifications Extension Cords Volt Single Phase OperationFunctional Description Carton ContentsSheet Metal Cast Iron Cast Iron Extension Extension Wings Extension WingsStand Parts Unpacking and Cleaning AssemblyAssembly Tools Required HardwareStand to SAW Stand LegsBlade Tilting Raising Handwheel Installing Switch Motor Cord Motor to Motor Mounting Plate Disconnect Machine from Power SourceMotor and Motor Mounting Plate to SAW PIN X , Through the Inside Hole of Bracket BMotor PULLEY, Pulley GUARD, and Drive Belt Illustrates the motor cord connected to the switch assembly Connecting Motor Cord to Switch AssemblyBlade Guard and Splitter Assembly and Alignment Page Model 36-649 only ON/OFF SwitchModel 36-678 only Model 36-679 onlyOperation Locking Switch in the OFF PositionStarting and Stopping SAW Overload ProtectionTilting the Blade Raising and Lowering BladeTable Insert a should Always be Level with the Table Miter Gage Operation and AdjustmentAdjusting Table Insert Open end wrench B Changing the SAW BladeCROSS-CUTTING Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGConstructing a Push Stick RippingUsing Moulding Cutterhead Accessory Moulding CutterheadUsing Accessory Dado Head Constructing a Featherboard Using Auxiliary Wood Facing on RIP FencePower Tool Institute Constructing a Push Stick TroubleshootingWarranty MaintenanceService Model 36-648 30 Fence and Rail System Model DescriptionModel U30 30 Unifence Model BC30 30 Biesemeyer Commercial FenceCanadian PORTER-CABLE Delta Service Centers
Top Page Image Contents