Grizzly G0716 Grounding & Plug Requirements, Extension Cords, Minimum Gauge Size 14 AWG, 50 ft

Page 12

Grounding & Plug Requirements

This machine MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current.

This machine is equipped with a power cord that has an equipment-grounding wire and a ground- ing plug (similar to the figure below). The plug must only be inserted into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances.

Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual.

GROUNDED

5-15 RECEPTACLE

Grounding Prong

5-15 PLUG

Neutral Hot

Figure 2. Typical 5-15 plug and receptacle.

SHOCK HAZARD!

Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground.

Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment-grounding wire. If repair or replacement of the power cord or plug is nec- essary, do not connect the equipment-grounding wire to a live (current carrying) terminal.

Check with a qualified electrician or service per- sonnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded. If you ever notice that a cord or plug is damaged or worn, discon- nect it from power, and immediately replace it with a new one.

Extension Cords

We do not recommend using an extension cord with this machine. If you must use an extension cord, only use it if absolutely necessary and only on a temporary basis.

Extension cords cause voltage drop, which may damage electrical components and shorten motor life. Voltage drop increases as the extension cord size gets longer and the gauge size gets smaller (higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle, and meet the following require- ments:

Minimum Gauge Size

14 AWG

Maximum Length (Shorter is Better)

50 ft.

-10-

Model G0716 (Mfg. Since 2/11)

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model G0716 Drum Sander Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification Model G0716 identificationMachine Data Sheet Drum Information Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Additional Safety for Drum Sanders Power Supply AvailabilityFull-Load Current Rating Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupUnpacking Description QtyInventory Inventory Figure QtyHardware Recognition Chart Site Considerations Assembly To assemble the drum sanderStep Page Dust collection elbow installed Dust Collection Power Connection Connecting PowerDisconnecting Power To connect a dust collection hoseRecommended Adjustments Factory adjustments that should be verifiedTest Run To test run the machineOperations Basic ControlsWorkpiece Inspection SandpaperSelection Before sanding, inspect all workpieces for the followingReplacement Remove Gray Areas On Both EndsItems Needed Qty To replace the sandpaper stripPage Sandpaper Goes here To adjust the depth of cut Depth of CutAccessories on Feed RateSanding Tips Sanding Operation To surface sand a workpieceAccessories G1512 Pro-StikBelt CleanerMaintenance General CleaningCleaning Sandpaper Lubrication ScheduleService TroubleshootingSymptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Conveyor Belt Tension & Tracking Belt TensionBelt Tracking Tools Needed QtyGib Adjustment To adjust the gibsConveyor Belt to Drum Alignment IncorrectPressure Roller Adjustment To adjust the pressure rollersTool Needed Qty Adjusting Elevation Stop To adjust the elevation stop screwConveyor Belt Replacement To replace the conveyor beltWiring Wiring Safety InstructionsG0716 Wiring Diagram Switch wiringParts StandConveyor Conveyor Parts List Main Main Parts List DescriptionMachine Labels Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY

G0716 specifications

The Grizzly G0716 is a versatile and robust wood lathe designed for both amateur and professional woodworkers. With its powerful motor and impressive features, this lathe stands out in the woodworking community for its reliability and performance.

At the heart of the Grizzly G0716 is a 1 HP motor, which delivers high torque and allows for smooth operation at various speeds. The lathe offers variable speed capabilities ranging from 400 to 3,600 RPM, providing woodworkers with the flexibility to adjust the speed based on the material and application. This feature is particularly beneficial for turning different types of wood, ensuring optimal results for both roughing and finishing cuts.

The G0716 has a sturdy cast iron construction, which contributes to its stability and minimizes vibrations during operation. This solid build not only ensures durability but also enhances the overall turning experience, leading to more precise and consistent results. The spacious bed length of 32 inches provides ample space for working on larger projects, making it suitable for various applications, from bowls to larger spindles.

One of the standout characteristics of the Grizzly G0716 is its user-friendly design. It includes a sliding tailstock that allows for easy adjustments and precise alignment, facilitating seamless operation. The quick-release tailstock and easy-to-read indexing head enhance usability, allowing woodworkers to switch between different projects without unnecessary delays.

In terms of safety, the lathe is equipped with a safety switch that prevents accidental start-up, ensuring that users remain protected during operation. Additionally, the machine's well-placed controls allow for convenient access, so operators can stay focused on their work while easily making adjustments as needed.

The G0716 is compatible with a variety of tools and accessories, increasing its versatility and making it a valuable addition to any workshop. Whether you are a beginner looking to explore the world of turning or an experienced woodworker seeking a reliable lathe for your projects, the Grizzly G0716 offers a blend of power, precision, and practicality that enhances the woodworking experience. Its combination of features, safety elements, and robust construction sets a standard for quality lathes in its class.
Top Page Image Contents