Grizzly G0716 owner manual Test Run, Recommended Adjustments, To test run the machine

Page 21

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation.

The test run consists of verifying the following:

1)Both motors power up and run correctly, and

2)the safety disabling mechanism on the switch works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 30.

To test run the machine:

1.Make sure you have read the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Make sure the sanding drum is safely above the conveyor belt so that it will not make con- tact when running.

4.Verify that the machine is operating correctly by turning it ON.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

5.Rotate the conveyor variable feed rate dial clockwise to verify the conveyor belt feed rate changes, then turn it counterclockwise until the belt stops.

6.Turn the machine OFF.

7.Remove the switch disabling key, as shown in Figure 15.

Model G0716 (Mfg. Since 2/11)

Figure 15. Removing switch key from paddle

switch.

8.Try to turn the start the machine with the paddle switch.

—If the machine does not start, the switch disabling feature is working as designed.

—If the machine starts, immediately stop the machine. The switch disabling feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

Recommended

Adjustments

For your convenience, the adjustments listed below have been performed at the factory.

However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine.

Step-by-step instructions for these adjustments can be found on the referenced page for each item.

Factory adjustments that should be verified:

•Conveyor belt tension and tracking (Page 33)

•Gib adjustment (Page 34)

•Conveyor belt to drum alignment (Page 35)

•Pressure roller adjustment (Page 36)

•Adjusting elevation stop (Page 37)

-19-

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model G0716 Drum Sander Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Model G0716 identification IdentificationMachine Data Sheet Drum Information Safety Instructions for Machinery SafetyUnattended OPERATION. Never­ leave­ Additional Safety for Drum Sanders Availability Power SupplyFull-Load Current Rating Circuit RequirementsExtension Cords Grounding & Plug RequirementsMinimum Gauge Size 14 AWG 50 ftNeeded for Setup SetupUnpacking Description QtyInventory Figure Qty InventoryHardware Recognition Chart Site Considerations Assembly To assemble the drum sanderStep Page Dust collection elbow installed Connecting Power Dust Collection Power ConnectionDisconnecting Power To connect a dust collection hoseFactory adjustments that should be verified Recommended AdjustmentsTest Run To test run the machineBasic Controls OperationsSandpaper Workpiece InspectionSelection Before sanding, inspect all workpieces for the followingRemove Gray Areas On Both Ends ReplacementItems Needed Qty To replace the sandpaper stripPage Sandpaper Goes here Depth of Cut To adjust the depth of cutAccessories on Feed RateSanding Tips To surface sand a workpiece Sanding OperationG1512 Pro-StikBelt Cleaner AccessoriesGeneral Cleaning MaintenanceCleaning Sandpaper Lubrication ScheduleTroubleshooting ServiceSymptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Belt Tension Conveyor Belt Tension & TrackingBelt Tracking Tools Needed QtyTo adjust the gibs Gib AdjustmentIncorrect Conveyor Belt to Drum AlignmentPressure Roller Adjustment To adjust the pressure rollersTool Needed Qty To adjust the elevation stop screw Adjusting Elevation StopTo replace the conveyor belt Conveyor Belt ReplacementWiring Safety Instructions WiringSwitch wiring G0716 Wiring DiagramStand PartsConveyor Conveyor Parts List Main Description Main Parts ListMachine Labels Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY

G0716 specifications

The Grizzly G0716 is a versatile and robust wood lathe designed for both amateur and professional woodworkers. With its powerful motor and impressive features, this lathe stands out in the woodworking community for its reliability and performance.

At the heart of the Grizzly G0716 is a 1 HP motor, which delivers high torque and allows for smooth operation at various speeds. The lathe offers variable speed capabilities ranging from 400 to 3,600 RPM, providing woodworkers with the flexibility to adjust the speed based on the material and application. This feature is particularly beneficial for turning different types of wood, ensuring optimal results for both roughing and finishing cuts.

The G0716 has a sturdy cast iron construction, which contributes to its stability and minimizes vibrations during operation. This solid build not only ensures durability but also enhances the overall turning experience, leading to more precise and consistent results. The spacious bed length of 32 inches provides ample space for working on larger projects, making it suitable for various applications, from bowls to larger spindles.

One of the standout characteristics of the Grizzly G0716 is its user-friendly design. It includes a sliding tailstock that allows for easy adjustments and precise alignment, facilitating seamless operation. The quick-release tailstock and easy-to-read indexing head enhance usability, allowing woodworkers to switch between different projects without unnecessary delays.

In terms of safety, the lathe is equipped with a safety switch that prevents accidental start-up, ensuring that users remain protected during operation. Additionally, the machine's well-placed controls allow for convenient access, so operators can stay focused on their work while easily making adjustments as needed.

The G0716 is compatible with a variety of tools and accessories, increasing its versatility and making it a valuable addition to any workshop. Whether you are a beginner looking to explore the world of turning or an experienced woodworker seeking a reliable lathe for your projects, the Grizzly G0716 offers a blend of power, precision, and practicality that enhances the woodworking experience. Its combination of features, safety elements, and robust construction sets a standard for quality lathes in its class.
Top Page Image Contents