Grizzly G0716 owner manual Feed Rate, Sanding Tips, Accessories on

Page 28

Feed Rate

Setting the proper feed rate is a matter of experi- ence and good judgement. When selecting the feed rate for the operation, consider variables such as the hardness and condition of the wood, the sandpaper grit being used, the finish desired, etc.

As a guideline, wide or hard workpieces, or using finer grit sandpaper will require a slower feed rate. The goal in setting the correct feed rate is to pro- duce the desired results for the operation without burning the workpiece.

NOTICE

Using too fast of a feed rate may exceed the sanding motor capacity and trip the motor or power supply circuit breaker. Using too slow of a feed rate may burn the surface of the workpiece.

To adjust the conveyor belt feed rate, rotate the conveyor variable feed rate dial shown in Figure 25.

Feed Rate

Dial

Figure 25. Location of the feed rate dial.

Note: The ON/OFF switch must be in the ON position to enable the conveyor motor to run.

-26-

Sanding Tips

Follow these precautions to ensure safe sanding operation and quality results:

•Replace the sandpaper with a higher grit to achieve a finer finish (refer to Sandpaper on

Page 21).

•When making multiple passes on the workpiece, do not lower the sanding drum more than 1⁄32" or 1⁄4 turn of the elevation handwheel for any one pass.

•If possible, feed the workpiece at a 60° angle to the sanding drum. This will provide for more effective material removal, less loading and more even wear of the sandpaper, and lighter load on the motors. On the last finish- ing passes, feed the workpiece so that the majority of the grain is perpendicular to the sanding drum.

•Extend the life of the sandpaper by regularly using a PRO-STICK© sanding pad (refer to

Accessories on Page 28).

•Reduce snipe when sanding more than one board of the same thickness by feeding them into the sander with the front end of the sec- ond board touching the back end of the first board.

•DO NOT edge sand boards. This can cause boards to kickback, causing serious personal injury. Edge sanding boards also can cause damage to the conveyor belt and sandpa- per.

•When sanding workpieces with a bow or crown, place the high point up (prevents the workpiece from rocking) and take very light passes.

Model G0716 (Mfg. Since 2/11)

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Model G0716 Drum Sander Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification Model G0716 identificationMachine Data Sheet Drum Information Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Additional Safety for Drum Sanders Power Supply AvailabilityFull-Load Current Rating Circuit RequirementsGrounding & Plug Requirements Extension CordsMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupUnpacking Description QtyInventory Inventory Figure QtyHardware Recognition Chart Site Considerations To assemble the drum sander AssemblyStep Page Dust collection elbow installed Dust Collection Power Connection Connecting PowerDisconnecting Power To connect a dust collection hoseRecommended Adjustments Factory adjustments that should be verifiedTest Run To test run the machineOperations Basic ControlsWorkpiece Inspection SandpaperSelection Before sanding, inspect all workpieces for the followingReplacement Remove Gray Areas On Both EndsItems Needed Qty To replace the sandpaper stripPage Sandpaper Goes here To adjust the depth of cut Depth of CutFeed Rate Accessories onSanding Tips Sanding Operation To surface sand a workpieceAccessories G1512 Pro-StikBelt CleanerMaintenance General CleaningCleaning Sandpaper Lubrication ScheduleService TroubleshootingSymptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Conveyor Belt Tension & Tracking Belt TensionBelt Tracking Tools Needed QtyGib Adjustment To adjust the gibsConveyor Belt to Drum Alignment IncorrectTo adjust the pressure rollers Pressure Roller AdjustmentTool Needed Qty Adjusting Elevation Stop To adjust the elevation stop screwConveyor Belt Replacement To replace the conveyor beltWiring Wiring Safety InstructionsG0716 Wiring Diagram Switch wiringParts StandConveyor Conveyor Parts List Main Main Parts List DescriptionMachine Labels Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY

G0716 specifications

The Grizzly G0716 is a versatile and robust wood lathe designed for both amateur and professional woodworkers. With its powerful motor and impressive features, this lathe stands out in the woodworking community for its reliability and performance.

At the heart of the Grizzly G0716 is a 1 HP motor, which delivers high torque and allows for smooth operation at various speeds. The lathe offers variable speed capabilities ranging from 400 to 3,600 RPM, providing woodworkers with the flexibility to adjust the speed based on the material and application. This feature is particularly beneficial for turning different types of wood, ensuring optimal results for both roughing and finishing cuts.

The G0716 has a sturdy cast iron construction, which contributes to its stability and minimizes vibrations during operation. This solid build not only ensures durability but also enhances the overall turning experience, leading to more precise and consistent results. The spacious bed length of 32 inches provides ample space for working on larger projects, making it suitable for various applications, from bowls to larger spindles.

One of the standout characteristics of the Grizzly G0716 is its user-friendly design. It includes a sliding tailstock that allows for easy adjustments and precise alignment, facilitating seamless operation. The quick-release tailstock and easy-to-read indexing head enhance usability, allowing woodworkers to switch between different projects without unnecessary delays.

In terms of safety, the lathe is equipped with a safety switch that prevents accidental start-up, ensuring that users remain protected during operation. Additionally, the machine's well-placed controls allow for convenient access, so operators can stay focused on their work while easily making adjustments as needed.

The G0716 is compatible with a variety of tools and accessories, increasing its versatility and making it a valuable addition to any workshop. Whether you are a beginner looking to explore the world of turning or an experienced woodworker seeking a reliable lathe for your projects, the Grizzly G0716 offers a blend of power, precision, and practicality that enhances the woodworking experience. Its combination of features, safety elements, and robust construction sets a standard for quality lathes in its class.
Top Page Image Contents