Grizzly G1022SM Attaching a sacrificial fence, To install and adjust the Model Z fence

Page 30

Tip: Attach a piece of 3Ú4" thick hardwood to the blade side of the fence as shown in Figure 29. This will keep thin materials from wedging between the fence and table and will also protect the fence from coming in contact with the blade when dadoing or ripping thin stock. Remember to flip and adjust the mea- surement scale on the rail to compensate for the thickness of the sacrificial fence.

Sacrificial Fence

Rip Fence

Wood Screws

Figure 29. Attaching a sacrificial fence.

To install and adjust the Model Z fence:

1.First, make sure the front clamp is engaging the front rail with the lock handle at one-half of its throw.

2.If the front clamp requires adjustment, loosen the check nut shown in Figure 30. Turn the adjusting bolt clockwise if the front clamp is too far from the rail, counter-clock- wise if it is too close.

Adjusting Bolt

Check Nut

Figure 30. Adjusting clamp mechanism.

3.Slide the fence along the rail until it is aligned with the edge of the miter slot.

4.Lock the fence down.

5.Loosen the rear lock adjustment (the slotted screw on the front of the fence shown in Figure 31) until the rear locking clamp ceases to engage the rear rail with the fence in the locked position.

Rear Lock Adjustment

Figure 31. Rear lock adjustment screw.

-28-	G1022 Series Table Saws

Image 30

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksZero Clearance Table Inserts Push PaddlesFeatherboards Introduction CommentaryG1022 Series Table Saws Models SM & Z Circuit Requirements110V Operation Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltFloor Load Clean UpSite Considerations Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings Fence To install and adjust the Model SM fenceFence Rails To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog