Grizzly G1022SM instruction manual Additional Safety Instructions For Table Saws

Page 6

Additional Safety Instructions For Table Saws

1.THRU-SAWING:Use blade guard, splitter, and anti-kickback fingers on all thru-saw- ing operations. See Page 12 for the defin- ition of thru-sawing.

2.KICKBACK: Use anti-kickback devices during ALL cutting operations. If you do not have a complete understanding of how kickback occurs, or how to prevent it, Do not operate this table saw. See Page 12 for the definition of kickback.

3.DANGEROUS REACHING: Do not reach behind or over the saw blade with either hand while the saw is running.

4.PUSHSTICK: Use a push stick when rip- ping narrow stock.

5.FREE-HAND CUTTING: The fence or the miter gauge must support the workpiece during all cutting operations.

6.BODY POSITION WHEN CUTTING: Do not stand or have any part of your body in- line with the path of the saw blade.

7.WORKPIECE CONTROL: Hold the work- piece firmly against the miter gauge or fence and hold the workpiece firmly against the table.

8.CROSSCUTTING: Move the rip fence out of the way when crosscutting.

9.MITER GAUGE/RIP FENCE: Never use the miter gauge and rip fence at the same time.

10.STALLED BLADE: Never attempt to free a stalled saw blade without first turning the saw off.

11.CUTOFF TABLES: Use adequate support to the rear and sides of the saw table for wide or long workpieces.

12.HAND SAFETY: Avoid awkward cutting operations and hand positions where a sudden slip could cause your hand to move into the saw blade.

13.SAW BLADE: Lower the saw blade below the table when not in use.

14.DAMAGED SAW BLADE: Never use a damaged saw blade or one that has been dropped.

15.DADO CUTTING: There is a high degree of risk involved with any dado operation. See Page 12 for the definition of dado.

Unfamiliarity with this manual could result in serious personal injury. Become familiar with the contents of this manual, including all the safety warnings.

No list of safety guidelines can be com- plete. Operating this machinery may require additional safety precautions spe- cific to your shop environment. Failure to use reasonable caution while operating this machine could result in serious per- sonal injury.

-4-	G1022 Series Table Saws

Image 6

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksZero Clearance Table Inserts Push PaddlesFeatherboards Introduction CommentaryG1022 Series Table Saws Models SM & Z Circuit Requirements110V Operation Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltFloor Load Clean UpSite Considerations Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyHandwheels All ModelsTo mount the handwheels Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings Fence To install and adjust the Model SM fenceFence Rails To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertMiter Gauge Initial Step Models ZF, ZFX, PROZ, & ProzxNext steps for all models Start Up Recommended Adjustments Recommended adjustment checklistStarting the machine Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubrication BeltLubricate the areas indicated below every 12 months Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog