Grizzly G1022SM instruction manual Rabbet Cutting, Sacrificial fence G1022 Series Table Saws

Page 44

7.Re-adjust the fence so the blade is aligned with the other edge of the intended dado channel. Be sure to keep the cuts within your marks; otherwise, the dado will be too big.

8.Continue making cuts toward the center of the dado with your subsequent cuts until the dado is complete.

Always replace the blade guard after dado- ing is complete. Failure to follow this warn- ing could result in serious personal injury.

Rabbet Cutting

Commonly used in furniture joinery, a rabbet is a straight groove cut in the edge of the workpiece. Rabbets can be cut using either a dado blade (Figure 49) or a standard saw blade.

Rabbet operations present very real haz- ards requiring proper procedures to avoid serious injury. The chance of kickback is always greater when dado blades are used so extra care must be taken. Any movement of the stock away from the fence will cause kickback. Be certain that stock is flat and straight. Failure to follow these warnings could result in serious personal injury.

To attach a sacrificial fence:

Rabbet cutting with a dado blade requires the use of a sacrificial fence attachment as shown in Figure 54.

Sacrificial Fence

Wood Screws

Dado Insert

Rip Fence

Figure 54. Sacrificial fence.

-42-	G1022 Series Table Saws

Image 44

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksFeatherboards Zero Clearance Table InsertsPush Paddles Introduction CommentaryG1022 Series Table Saws Circuit Requirements 110V OperationModels SM & Z Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyTo mount the handwheels HandwheelsAll Models Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings To install and adjust the Model SM fence Fence RailsFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertNext steps for all models Miter GaugeInitial Step Models ZF, ZFX, PROZ, & Prozx Starting the machine Start Up Recommended AdjustmentsRecommended adjustment checklist Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubricate the areas indicated below every 12 months LubricationBelt Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog