Grizzly G1022SM instruction manual Blade, Changing saw blade G1022 Series Table Saws

Page 32

Blade

To install a saw blade:

1.Disconnect the machine from the power source!!

2.The arbor nut has left-hand threads. Unthread the arbor nut clockwise and remove the outside flange from the arbor. Remove and discard the 3Ú4'' diameter spacer on the arbor shaft.

Use caution and remain alert when working with the saw blade. Failure to follow this warning could result in serious personal injury or death.

3.Install the saw blade onto the arbor. Ensure that the blade teeth point toward you as you stand at the front of the saw.

4.Slide on the flange and thread the arbor nut back on.

5.Use the arbor wrench provided with the saw to tighten the arbor nut. Wedge a block of wood in the teeth of the blade to keep it from turning when tightening the nut as shown in Figure 35.

!

Figure 35. Changing saw blade.

-30-	G1022 Series Table Saws

Image 32

Contents G1022SM G1022Z G1022ZF G1022ZFXPage Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksFeatherboards Zero Clearance Table InsertsPush Paddles Introduction CommentaryG1022 Series Table Saws Circuit Requirements 110V OperationModels SM & Z Model ZF220V Operation Models ZFX, PROZ, & ProzxGrounding Extension CordMachine Features Terms and DefinitionsMain Features SET UP Unpacking Piece InventoryMotor with Pulley Hardware Contents Hardware Recognition Chart BoltClean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Stand Assembly Stand completely assembled Models ZF, ZFX, PRO, & Prozx onlyTo mount the handwheels HandwheelsAll Models Motor Checking V-belt alignment Switch Models ZF, ZFX, PROZ, & ProzxExtension Wings To install and adjust the Model SM fence Fence RailsFence To mount the rails Models SM & ZAdjust measurement pointer G1022 Series Table Saws To install and adjust the Model Z fence Attaching a sacrificial fenceAttaching a sacrificial fence G1022 Series Table Saws Blade Changing saw blade G1022 Series Table SawsInstalling blade guard Blade GuardProper Alignment Added Washers Adjusting table insert components G1022 Series Table Saws Table InsertNext steps for all models Miter GaugeInitial Step Models ZF, ZFX, PROZ, & Prozx Starting the machine Start Up Recommended AdjustmentsRecommended adjustment checklist Operations Blade SelectionVarious saw tooth cutting profiles G1022 Series Table Saws Crosscutting Cross-cut operation G1022 Series Table SawsRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1022 Series Table SawsDisconnect the machine from the power Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1022 Series Table Saws Maintenance GeneralLubricate the areas indicated below every 12 months LubricationBelt Date Approximate Hours Of Use Maintenance Performed Service Adjustments Blade ParallelismShim placement G1022 Series Table Saws To shift the trunnionTo shim the trunnion 45˚ & 90˚ Stops Closure SM and Z Wiring Diagram ZF, ZFX, Proz & Prozx Wiring Diagram Machine Data Sheet G1022SM G1022SM G1022SM G1022SM Parts List PRP02M Grizzly Model G1022Z Table SAW G1022Z G1022Z G1022Z G1022Z Parts List Pulley Guard Bracket Grizzly Models G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx G1022ZF, ZFX, PROZ, & Prozx Parts List Switch L-BRACKET Troubleshooting Guide Symptom Possible Cause Corrective ActionPush Stick G1022 Series Table Saws G1022 Series Table Saws Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA Page Call Today For a Free Full Color Catalog